I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I'm attempting Mesh DFU on an Ubuntu 16.04 system. Here are the steps in the quick start guide along with corresponding notes on my setup:
nrfutil keys --gen-key private_key...
We are currently developing on the PCA10056 as we wait for our development boards. We would like to implement UART0 as a debug port, that we can output the log messages to...
Hi,
Can somebody explain how the Ax, Bx and Tx registers are used in the calculation of the temperature reported by the temperature sensor block in an nRF52832?
What we...
Hi,
I need to connect multiple SPI slaves in a daisy chain. It seems that using nrfx_spim_init once and nrfx_spim_xfer at each transfer is the simplest way to go using the...
hello, i want to synchronyze differents peripheral with a central thanks to the state of gpio i have this code but when i call gpiote() i hava nothing in return why ?
void...
I have done some reading on the forums and have seen that Martin Bohrs-Lind has ported the EMDv6.12 to SDKv14.2 and the nRF52832, here . I have keil v 5 compiling his work...
Hi
What would be the best way to interface a wireless charging circuit with a nRF52 device?
I've found a IC from Texas instruments that does the job, but is it safe to...
Hello,
I am using sdk12.2.2 and nrf52832 customized board. I am putting mcu to sleep mode using sd_power_system_off. Now when I am pressing button for first time I am not...
Using the include files and .dll file from
www.nordicsemi.com/.../nRF51822 -> "DOWNLOADS" -> "nRF51-BLE-Driver-Win" I have created a C# wrapper for the driver. I works so...
Hello,
I'm using multiple GPIO pins as inputs. Should I use nrf_drv_gpiote_in_event_enable() for each pin? Also how to configure the input_event_handler() to handle the...
Hello,
I'm a beginner on BLE protocol and i would like to send data during approximately 4us,stop it during the same time and transmit signal again during 4us and so on...
Hi
I’ve downloaded nRF5_SDK_11.0.0_89a8197 and starting with examples from \examples\ble_peripheral\???\pca10040\s132\arm5_no_packs\
I'm writing an application to be running...
Hi
I am new to ARM and Nordic programming.
I want to send one HEX byte via SPI.
It works with some HEX numbers and with some numbers it wont.
0x13 / 0x15 work
0x14...
I wonder if it is OK to change the lpcomp ref input on the fly, without any other stop task or disable/enable. Just like this:
//--------------------
static void lpcomp_set_ref...
i want to print the data to the uart to see the values in the uart..i am unable to initialize the uartt..
what are the things to be added for the initialization of the uart...
