Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I am having interface nRF51 with RF receiver. Output of RF receiver connected with GPIO pin of nRF51.
How can I detect interrupt on gpio pin?
Thanks & Regards...
Hi,
I'm using Secure_Bootloader example of SDK 15.0.0 and I can't get the Logger module to work. I set NRF_LOG_ENABLED to 1, increased memory regions in make file, so the...
Can the esb bugfix timer (currently TIMER_3) be set to another un-used timer without any side effects? I need to implement the async uart from SDK15 and it uses TIMER_3 and...
Is there a simple example which supports LESC Just Works for peripheral mode only? The lesc_multirole example seems a bit too much since that also supports central role. I...
I am sampling 3 sensors using the ADC peripheral, clocking it once every 15us to sample the 3 sensors (3us acquisition time + 2us processing = 5us per channel).
I use the...
hi,
How can i set Destination Address to a particular Mesh Node. so that all message reach that particular Node Only.Since provisioner can set address while provisioning...
how to use app of mesh to send message to node ?
I already got the source code from web: https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library .
1\ i have add three...
I would like to put a nrf51822 device into system sleep (not off) mode and wake it up (not reset) with a GPIO transition from high to low. I used SDK(nRF5_SDK_12.2.0_f012efa...
Hello everybody, I tried to activate the PHY Coded in the UART Example from the SDK15.1.0 examples.
For this purpose, I have set NRF_BLE_SCAN_SCAN_PHY 4 in the sdk_config...
hello,we are developing NFC on NRF52832 recently,we want to use NFC as a label,T4T,but we have some problems as follows:
1、firstly,we want to develop NFCT by ourselves(not...
hello , i'am working actually on the timer of nRF52840 S140
my timer look like this:
but how to switch from millisecond resolution to microsecond resolution ? ( APP_TIMER_TICKS...
Hi!
I've try to made bootloader/recovery application that should to replace existing run-time application of the device. The F/W file for replacement placed in external...
Hello,
I am using Eclipse with ARM toolchain on ubuntu to buid my application with softdevice s132 api version 3.1.0. I managed to build on eclipse and merge softdevice...
We have a GPIO configured in the GPIOTE to generate an interrupt on the LotoHi and HitoLo transitions (Toggle). Inside the interrupt handler we would like to perform a slightly...
