Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello, I am new to nRF micro-controllers and using Netbeans. I have cloned the repo of a project I would like to run, which builds successfully, and am getting the following...
Two questions. 1) What is the point of the watchdog ISR? In the Ambiq Apollo 2 microcontroller, the watchdog ISR fires and if the CPU doesn't pet the watchdog slightly after...
Hello I have problem with Mesh Serial Example and Interactive_pyaci, it works just in Debug-Mode. I use nRF52840, nRF5_SDK_15.0.0_a53641a, nrf5_SDK_for_Mesh_v2.0.1, Python3...
Hi I am trying to optimize my nrf51 app for low power. However I can just reach 0,500mA when just advertising (advertisement only is ok for me). Do you know or do you have...
I am trying to integrate the NFC read/write functions in my BLE application. I have used the writable_ndef_msg project functions to start with. The project on its own works...
Hello
For my final year project at Varsity I am creating my own smartwatch + edge computing IoT system. The watch and infrastructure needs to be as low-cost as possible...
Hi,
I am using a nRF52 DK board and programming in python.
After performing a successful DFU over BLE i want my Target device to be disconnected from the nRF board so...
thanks for the answer on the previous post.
What I came to know from our firmware engineer was that your initial version of the Android app could not support
1. multiple...
I want to know 2 things about the nRF Mesh app:
1) Is it possible for the Mesh app to provision non-proxy nodes via the proxy nodes?
2) I think it's possible to subscribe...
I have a project using FreeRTOS with Tickless idle enabled, SDK 11.0.0 alpha and the S132 soft device. Currently the project is consuming ~6.5mA average, ~5.2mA if advertising...
Hi There,
I very new to Nordic BLE application and was looking for method to combine ble_app_beacon and ble_app_blinky togather and having both switching and running at...
Hi:
In the datasheet, there have a description
Input range = (+- 0.6 V or +-VDD/4)/Gain
for a example, if Gain = 2, reference = 0.6V,
input range = 0.6 / 2 = 0...
In the SDK12.3.0 example ble_app_hrs_rscs_relay I want to add a uart to this example I added the uart_init part and the nus part, referring to ble_app_uart. However, when...
Hello,
What are the maximum number of node our nrf52832 and 52840 can support for
Zigbee?
BLE?
Thread - 1000?
Would this number be dependent on the memory size?...
