I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi All,
Has anyone had to go through the new Rx RF Blocking test specified in the new version of EN 300 328? It seem all products shipped to the EU after June 2017 need...
Hi
I am working with nRF52840 , since it is said that it can work on 64Mhz, i just want to confirm by using Oscilloscope.
You have any inputs that how i can check the...
Hi,
I am newbie to Nordic and I am building a program that samples adc value. I just wanna know about the difference between two functions "nrf_drv_adc_buffer_convert"and...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Does the S110 v7.0.0.3-alpha DFU bootloader support nRF51822XXAB (128k) part?
I'm trying to flash the DFU bootloader on my custom PCB that contains a nRF51822XXAB part...
Hello
I have an application to process advertising report even if it is duplicated.
Is there any way to control whether the soft deice shall filter
duplicate advertising...
Hello,
I am using the example "ble_app_beacon", I have compiled and tested (all works well).
I am wanting to add more data to the scan response by passing more data to...
I'd like to run a softdevice application with OTA support on a RIGADO BMD-200 Evaluation board . I've successfully flashed the softdevice, the app, and the rigado bootloader...
I have a simple application which pretty much consists of the following main function:
int main(void)
{
SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL);
ble_enable_params_t...
Hi,
We're working on BLE communication between iOS and 51822 and found a data reliability issue. We have a custom characteristics that iOS read 60 bytes data from 51822...
Hi,
I have made some changes with how we update tick timer inside FreeRTOS and the results are promising
.
The improvement is
RTOS tick will auto correct if masked...
I went through a similar post for nrf51 which explains the numbers pretty well ( devzone.nordicsemi.com/.../) . I wanted to know what the values are for nrf52. The internal...
We have a nrf51822 device that has to send 6 bytes back to back at 12K8 and 6-18 bytes at 38K4 in the future.
The bytes are in an array and do not need to be generated...
Hi experts,
I have just tried lbs example. I saw in the ble_lbs_c.h, the base uuid and service uuid are defined for the peripheral peers who are going to be connected....
