I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hi,
We are using nRF24L01+ modules on an ultrasonic positioning system. For synchronization, we wanted to use the RX and TX interrupts provided by the module to trigger...
Hi.
I'm currently trying to scan non-connectable advertisement for continuously.
it’s unclear to me. I doubt will be worked scanning 1000 peripherals.
so. i have to...
We are devolping a module with nRF52832-CIAA (CSP package) and we are not satisfied with the sensitivity.
According to the nRF52832 Errata is the sensitivity level different...
Dear all members,
I understand that Secure BLE DFU official support is only for SD132, but I am developing a product for nRF52810 which can only run SD112 and I want to...
This link source.android.com/.../services seems to indicate that L2CAP CoC is available in Android 8.x but support may vary by device vendor. Does anyone know how to verify...
Hi,
I just installed the latest NRF5 SDK - nRF5_SDK_15.0.0
and trying to run examples such as "examples\ble_peripheral\ble_app_hrs\pca10056\ser_s140_spi_5W"
But for...
We are developing a bluetooth product that operates on a battery where every uA counts and I have a couple of questions about current consumption in System On Low Power mode...
I am creating a BLE beacon scanner, using nRF51822 and SDK 12.0.0. My beacons will be using public addresses so the upper 3-bytes of device addresses of all my devises will...
Hi,
in our application we will have a main MCU and a second MCU, an nrf52832.
We need to update the fwon the nfr52832 from the main MCU using a bootloader, via UART. ...
Hello,
I want to use 2 SPI bus with nRF52832 IC and SDK5. I can use the "SPI example" for first SPI bus. For the second SPI Bus, I think that I need to modify "sdk_config...
My devices require calibration and self test to be carried out after programming. To implement this, my device checks the JLink reset pin (configured as a GPIO on my NRF52...
Hi everyone, I'm trying to implement a simple bluetooth beacon which broadcasts / advertises the number of button presses and the time in seconds after the last button press...
Hi everyone,
I'm trying to change the advertisement data while advertising using an interrupt. So far I've managed to use a button to change the advertisement data.
...
Hi,
I have huge BLE carrier frequency drift, which cannot pass FCC requirement.
The drift is 256kHz which seems not normal.
I'm using 32MHz 10ppm xtal so drift should...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
In my application I am using Peer Manager to manage bonding and also...
