Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi, even if I set hal_nrf_enable_ack_payload(false) on the sender (and receiver), the receiver still sends back an ACK which i can detect in the NRF_ISR(). is this normal...
Hello,
I have a pca10028 and I am wondering if I can use it also to flash nrf52 boards.
I quickly tried with rknrfgo on mac to wipe a custom board based on nRF52832 and...
Hello.
I decided to use an external solution for RTC.
Sometimes the RTC chip offers an buffered 32.768KHz output.
Can I use this output to supply the 32.768KHz to the nRF52832...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hai
i am using mbed to program my nrf5188. now i am using securityManager to implement a bonding between central and peripheral. now i need to know when a device is connected...
Hi,
In my code, I have not started the HF clock. I call the ble_stack_init where "SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);" is called. Which HF clock...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
The ble_app_uart includes "printf("\r\nUART Start!\r\n");" and "UART Start!" cames out on the putty...
I have a scenario where I have multiple peripherals (nRF52) and multiple centrals (cell phone).
The user is going to use only one central with only one peripheral together...
Hello
In case a connection is disconnected locally by calling sd_ble_gap_disconnect(), no BLE_GAP_EVT_DISCONNECTED is fired even though the sd_ble_gap_disconnect() function...
Hello, I'm trying to optimize power on HID Keyboard app.
This post was helpfull but yet some questions remains.
If I use several services, and want central to be abble...
After S110 7.1 ble_stack_init(), any read/write to temperature register cause a HardFault.
Some sentences like:
nrf_temp_init();
NRF_TEMP->TASKS_START = 1;
...
Hi --
I am using the ble_peripheral/ble_app_hrs example project. And if I try to update the vs_uuid_count param to 2. It proceeds to fail the softdevice_enable with error...
Hello,
I'm currently looking into the secure bootloader from the 12.2.0 SDK, and wondering if there is some example code regarding implementing a uart transport?
