I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
Hi,
I have two nrf52dk devices.
I Want to test the BLE examples which can exchange Bytes of information between each other and display over the UART.
Which examples...
Hi.
My target board has a power switch that is managed by GPIO.
First-time, a user clicks the button, the GPIO is turned on and the system wakes up.
In reset case(Firmware...
I'm troubleshooting my NFCT state machine -- I'm getting a lot of FRAMEDELAYTIMEOUT errors and can't understand why, I'm triggering a TXSTART ASAP... but that's another issue...
Hi there,
Is it possible to feed XC1 or XC2 with an oscillator output rather than using a crystal?
It would make sense for me in terms of application but I cannot see...
hello , I followed this tutorial : devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices
when i put the button 1 i have just a signal of 2 second...
Hello,
I want to use the D-/D+ as general I/O pins but noticed that it's not mentionned "General purpose I/O" in these pins.
Are these pins only available for USB ?...
Hi,
I am working with the examples/peripherals/application template code from SDK 15 against the brf52840-DK board. I am running Linux as my dev environment I am using the...
Hi there,
I was wondering if there was an easy way to output the LFCLK from our 32k crystal on one of the GPIO pins of the NRF52840?
Couldnt find anything in the Spec...
hello , i have 1 nordic card (central) and 4 nordic card (peripheral).
At this moment the 4 peripherals send their data to the central without problem one after the other...
Hi
I have RGB LED Strip of 5 numbers and giving out 5V from external power supply
This LED Strip has WS2811 as LED Driver ( https://cdn-shop.adafruit.com/datasheets/WS2811...
Dear all,
It's strange that this seems to not have been asked before... since the nRF52840 can be powered directly from a LiPo battery, I wonder if there is an UVLO protection...
Dears,
I am developing a board based on the nRF52-DK board and I noticed the technical documentation does not include the voltage ratings of the capacitors used. Could...
I am trying to make a large BLE sensor network, hypothetically anywhere from 20-100 devices in a STAR configuration. I see there is a 20 max limit on concurrent connections...
Hi,
I am trying to send a simple message from server to client in mesh 2.0.1. I am following this post for the same. I successfully sent a message from client to server...
When I want to connect the jlink use j-flash.exe.it report the follow message.My
Connecting ... - Connecting via USB to J-Link device 0 - Target interface speed: 4000 kHz...
