I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello,
I am developing Bluetooth 5.0 application which advertises two different beacon advertising data sets (Each set with different advertising interval)
I am using...
I'm using SDK 12.2.0, SofDevice 3.0 and my chip nRF52832.
In my boot-loader project i disable IS_SRVC_CHANGED_CHARACT_PRESENT by define to 0.
The dfu process is completed...
Hi
with SDK15 SD140 6.1.0. I'm trying to use BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_SCANNABLE_UNDIRECTED with CODED physical.
I run the following code
and getting...
Hello Community,
The PCB project I'm working on is ready to be optimized for production. What I am concerned with today is the electromagnetic compliance of the PCB.
In...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132.
In my project I have to implement passkey or whitelist in the conection with...
Hi,
I'm trying to run the OTA DFU for the nrf52832 (sdk v14.2, softdevice v5.1) from multiple devices.
In the OTA script, I enabl the receipt notifications and it works...
I am working out of this MPU-twi example and am trying to validate sent data by printing it to the serial monitor. From what I've seen in SDK 15.1.0 examples, it seems like...
Hi,
I am using nRF5 11.0.0 SDK softdevice 2.0.0.
I have implemented a RTOS application with beacon adv.
I also want to add UART service to the RTOS application.
...
Hi,
I am trying to use the Power Profiler Kit (PPK) to asses the power consumption on a nRF52840 - PDK. I have not managed to get anything wokring.
The exact hardware...
I am using 3 nRF 52840 dongles and want to establish mesh network between them. So I flashed the dongle with the softdevice (s140_nrf52_6.0.0_softdevice), bootloader (mesh_bootloader_serial_gccarmemb_nrf52840_xxAA...
I have flashed the the mesh serial hex file to nRF52840 dongle through nRF connect programmer application. I am getting following error
1. Reopen device failed
2. Nordic...
Hello All, In one of our product we are using nrf52840 Bluetooth + MCU IC. Size of Product is very tiny. which types of Antenna is better for range of 25 meter to 30 meter...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
