But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I'm trying to use the SEGGER debugger with one of the OpenThread examples for the nRF52840. When I click on the "Go" button, it asks for the location of the source files for...
I think I found a bug in ble_dfu_bonded.c.
In ble_dfu_buttonless_bootloader_start_prepare() there is a call to gscm_local_database_has_changed(). The problem is that this...
Hi,
How do i enable Gyroscope Support in Smart Remote FW v1.2?
When I enable this in the sr3_config_*.h file, setting "CONFIG_GYRO_ENABLED 1", I get an error stating:...
Hello,
I have moved my project from SES 3.34a to 3.40 and I see a new error at compilation.
When compiling the file nrf_pwr_mgmt.c’, I have the errors below :
unrecognizable...
While attempting to run the following code from a MESH example in IAR, the program gets stuck. It only seems to be calling button_event_handler continuously, as if the interrupt...
Hello,
I have been looking to program this IC, connecting via SWD with no luck. I can connect to the target but for some reason once i try to perform erase programming...
Hi!
What's the difference between UART_TX_BUF_SIZE and BLE_NUS_MAX_DATA_LEN in case of ble_app_uart example?
As I have noticed BLE_NUS_MAX_DATA_LEN determines maximum...
Hi,
I have a question about DFU mesh, I'm working on light switch demo and I combined light_switch_server with DFU exam ple in order to only u pdate server node with light_switch_server...
Very newbie question, so, sorry.
I am starting to use SES and the Find and Replace works fine in the same document, but if I do it for Replace in Files (Ctrl-Alt-F), it...
Hi,
I am using SDK14.2 with softdevice v5.1.0. I have recently ported my application from SDK12.2.
When I run my application with the softdevice it works fine. But when...
Hi everyone,
I'm in trouble with the stdlib of Keil SDK , which is nRF5_SDK_15.0.0_a53641a, while compliing.
The code what I add in the demo project causes Undefined...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
Hello,
We are testing a new device based on nRF52832. With our RF power meter the received power from the nRF52 is different if we use constant carrier or PBRS9 with 37...
Hi There,
I am trying to build an application that uses UART 0 (for debugging) and UART 1 (to read data over from a separate hardware). Simple objective is to send "Hello...
