I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
We have the following problem when start the watchdog from bootloader: the application is started successfully by the bootloader but when enable the softdevice the application...
Hello, I'm implementing a pair of MCUs where one is operating a ANT+/BLE radio stack using the S332 soft device. Whilst TWIS is disabled, we're getting great performance,...
Hi all , I using module NRF52832 and SDKv14 . I have 2 board central and 2 board peripheral . I want to connect each board central to all board peripheral and connect each...
Hi everyone,
I'm working in an application for a wearable device and I recently have a problem debugging it with Ozone Debugger from SEGGER Microcontroller Systems . I'm...
Hi I am using the mesh sdk 2.0.1 and the nrf52 dk board.
I have made a new model modifying the simple on of client/server example, where the server will send a periodic...
the function nrf_dfu_settings_init in nfu_dfu_setting.c
// Copy the DFU settings out of flash and into a buffer in RAM.
memcpy((void*)&s_dfu_settings, m_dfu_settings_buffer...
Hi,
Our product is based on BLE 4.2 / 5 peripheral devices and PC application (windows 7 & 10 environment) as central device.
we try to use nRF52840 dongle and also other...
On a NRF52DK Board, There is an on-board programmer done with ATSAM3U2C seen as a Segger programmer or a Jlink Progammer.
By mistake, I erased the entire flash of this...
I was trying to update J-link firmware (using link [https://devzone.nordicsemi.com/question/170895/nrf52832-jlink-stop-working-after-entering-bootloader-mode/] ) into interface...
Hi,
The following vulnerability described as Bluetooth implementations may not sufficiently validate elliptic curve parameters during Diffie-Hellman key exchange in the...
I want to use the serial DFU. Do you have any examples? I tried with ble_app_buttonless_dfu, not UART DFU.If you have a detailed reference, please let me know.thank you very...
Hi,
I am using the MCU on a board with sensors that are sampled in a very high rate (~100Hz).
I am having issues when trying to send the data with notification on more...
Hi,
I am using sdk12.2 and customised nrf52 board.
I want to interface ultrasonic sensor with nrf52. In this I am enabling trigger pin as high and after sometime my...
Dear All,
I am working with SDK version 15 and softdevice 132.
I want the device to advertise for 1 minute. Then go to low power mode. Again wake up after 5 minutes...
I have twe NRF24L01 module,one set Tx mode with autoask,and another set Rx mode without autoask,
The channel and address are same.
Can I use this mode to communication...
