Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
I've recently migrated from SDK11 to SDK12.3 to take advantage of the low power option. However I still am having weird issues with power consumption. I have a feature which...
I have merged all the 4 file's together (app.hex, app_valid_settings.hex, softdevice.hex and dfu.hex).
Then I uploaded the custom app with dfu services enabled using nrfgo...
Hi there,
I'm porting an app from NRF51 SD130 to NRF52 SD132, both with sdk11. I do the usual stuff, like changing includes, freertos ports libraries, etc, and everything...
Just a general resource question. The Softdevice uses RTC0, FreeRTOS (by coded default) uses RTC1. So in order for the SDK ble_conn_params.c to run properly I have to link...
I was able to add the Device Information service as well as a proprietary service using a 128 bit UUID. I modeled after the ble_peripheral uart example. However when I try...
Nrf52/Kiel/SDK11
My application was at the point where I needed to add DFU. Following the examples and SDK doc, I added the files and code needed. It would NOT advertise...
We recently moved from SDK11 to SDK13. We run out of memory when adding custom services & chars to the S132 v4.0 softdevice. Increasing the app start address in the linker...
For the record I have been struggling with migrating a project from S110 @ nrf51422 to S140 @ nrf52840.
Quite by accident, I found this "nrf51_to_nrf52840.h", what does...
Hi , Everyone!
Now i have the board nrf52832 and i'm conducting my DFU.
My DFU is to update softdevice and application.
Here is detail about my problem:
softdevice...
Hi
From s140_nrf52840_5.0.0-3.alpha_migration-document, it is mentioned that the L2CAP API has been completely removed. Are there plans to re-expose the API? We have exposed...
I'd like to clock the nRF52840 at the same frequency as my converters. Is there any problem with using a somewhat different frequency than the 64 MHz (or 32mhZ) crystal? If...
Hello guys,
i randomly get twi error busy 17.
i have #define TWI_DEFAULT_CONFIG_IRQ_PRIORITY 7 in sdk_config.h and .interrupt_priority = APP_IRQ_PRIORITY_LOW in init function...
My setup is based on a jlink clone and yunjia module nrf51822 and nRF51_SDK_10.0.0_dc26b5e. I am following this tutorial successfully till the section Enable auto discovery...
Hi,
The following function/macro is missing in SDK 12.2.0 and 12.3.0 but existed in 12.1.0:
nrf_drv_saadc_gpio_to_ain
I am re-compiling "thingy" SDK and it happens...