Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
Hi,
I want to use iOS to connect nRF82832 with passkey when connecting. I use pca10040_s132 with SDK 12.2.0.
Following is my procedure:
define security parameters...
Hi guys.
I'm trying to measure my battery. I'm testing my function from main and it works.
The procedure looks like this:
saadc init
sample data
saadc uninit...
I am using nrf52832 BLE chip(10040), sdk 12.2, softdevice s132 with sample example boot-loader code(dual bank).
I modified the boot-loader code for button-less DFU.
...
Hello,
I am using nrftoolbox code available here: github.com/.../IOS-nRF-Toolbox to perform the DFU procedure.
I have taken the firmware zip file.
I have integrated...
Is there a job board for Nordic developers? I'm offering a short contract job. I have a 100% complet e PCB design based on the Nordic chip. I'm looking for someone to write...
Hi.
I have a question.
I tested that nrf52 get datas from sensors.
But the code was not moved well,
I made code to test bit shift.
Please see my code.
#include <stdio...
I successfully built the example peripheral project "experimental_ble_app_queued_writes" from nRF5_SDK_12.0.0_12 and successfully downloaded the app to a nRF52832 development...
I have an arduino mega based design working with nrf24L01+ via SPI. As certification is the next step, I found a NRF52832 based module that would meet all certification requirements...
I've been trying to program a custom PCB with an nRF52832, using the nRF52 Development Kit and nRFgo Studio.
When I connect just the nRF52 Development Kit to my computer...
I'm an intern in my second year for a bachelor in computer engineering. I've been working with the nRF52832 development kit as part of my assignment. I was looking through...
Hi all,
I am experimenting with the DFU to switch between SDK versions from SDK12 to SDK13 and SDK13 to SDK12
Is it possible if I send a whole imagen of SD+BL+APP to...
Hi. I have a board here based on the nRF52832, using SD 132 and SDK 13.0.0, with a modem on it that I'd like to keep powered on even when the Nordic is in system off mode...
Currently I am using the NRF52 device to connect with a custom peripheral. The current goal I am trying to reach is toggling an LED by sending the command 0x8900 through Service...