I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
During the webcast earlier this week, we were shown a phone pairing with the nRF52 dev board using NFC.
Is the code used for that NFC demo available as an example project...
Hi,
I am using nRF52832 as the core of my device that works with battery. I have to keep the SoC powered on all the time. When the off push-button is pressed I restart...
I am using a nrf52832 to communicate via UART to a GSM module (AT commands).
I have setup the device with a baud rate of 9600 and using HW flowcontrol. The nrf52 is doing...
i want to communicate nrf52dk with arduino over spi.i want use nrf52dk as a master and ardunio as a slave.kindly refer me some example or code or any thing which s helpful...
Hi,
I'm working on migration from project based on SDK12.1.0, 132SD3.0.0 (calling A project) to the one based on SDK13.0.0, 132SD4.0.2 (calling B project).
I developed...
hello,
Please let me know why the BLE_GAP_EVT_DISCONNECTED event does not occur even when I exit the application.
It does not always occur when BT smart setting is enabled...
case 1: i use rtthread RTOS, main() disable global irq，on os scheduler enable global irq.
but i on task init stack, sd_softdevice_enable not return,system always reset.
...
The Device Family Pack 8.12 needed for the newly released
SDK 13.0.0 and SD S132 4.0.2 is missing from the download area.
Error #544: Required Software Pack 'NordicSemiconductor...
Hi everybody:
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
My last post showed that if BSP_SIMPLE is defined, I can't use button event trigger function...
Considering my use case, the size a certain characteristic is dynamic, and the notification should only contains the exact amount of data, even though locally there should...
Hello,
I'm using low power comparator with cross detection.
It works but I can't detect if it's failling or rising edge.
Can we detect simultaneously DOWN and UP...
Hi,Everyone! Now i have the board nrf52832 and i'm trying to get the battery value and send by using saadc.
i have read the example of ble_app_proximity and saadc,and i configure...
Hello! I compiled hex file with NRF52_BOOT in mbed cli. It was programmed successfully. Mbed os version include fix to use nrf52 DFUService. Bootloader is loading correctly...
