Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
I want to write calibration and configuration datas in to flash and read it back. By using sd_ble _flash_write API function , I can write up to 520 words(520* 4 bytes...
Hi, all!
nRF51822 had been used in my project, because of dual bank bootloader and softdevice, the
internal flash memory was not enough for the application. I want to...
Hi there,
I need to add more the function based on Bluetooth, and I need the better security of the function. However, I do not want others read flash data freely and I hope...
Hi
I'm preparing for some tests and I'm wondering where I can find information about what the expected percentage error rate should be?
Right now with 2 nrf boards connected...
Hello to all nordic jedi masters!
I have made an observation, on which I would like your confirmation.
My combo is: nrf52832 + SDK 11 + SD132.
Will my application ...
I'm currently writing my thesis, and my goal is to establish a network protocol like IP. We need to transmit about 200kB of data between 2 or more nodes once every 10-30 minutes...
I am programming a device with a NF52 that uses a hall effect switch o enter/exit sleep mode when BLE is in advertising mode. When connected, It will generate a separate BLE...
Hello,
i have a strange behaviour on a board with nRF52. The board is flashed with SD 4.0.2 and bootloader.
On Keil If i load the bootloader with JLink, it runs and...
I'm using nrfutil version 2.0.0 and have noticed a strange bug today when generating a new signed application image for bootloading.
If I have a version number of 0207...
hello , I am new to SPI protocol.I am using NRF52 DK &nRF5_SDK_13.0.0_04a0bfd( pca10040) using keil-5. I want spi master example code. Can any one suggested me where I find...
Hi there,
The S132 SoftDevice for the nRF52832 has grown in size from 0x1F000 for release 1.0.0-2.alpha, to 0x23000 for 5.0.0-3.alpha. It appears that the nRF52840 will...
I have a small PCB I'm prototyping/assembling, based on a nRF52832 with a few sensors. Looking for someone here to help me with writing basic firmware for testing the board...
Hi,
I am having trouble reading the contents of a record after the NFC tag in the microcontroller has been written by a smartphone.
I'm using the t4t emulator. When...