Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I asked what changed SDK11's "app_trace" to the SDK13.
You answered that the "app_trace" was changed in SDK12.
I found 'release note', but I could not find the above...
It appears that I must use S134 and S140 etc. Is it backward compatible? By that I mean I keep using S110/120 at the cost of not being able to utilize some of the latest feature...
Hi,
I want to use iOS to connect nRF82832 with passkey when connecting. I use pca10040_s132 with SDK 12.2.0.
Following is my procedure:
define security parameters...
Hi guys.
I'm trying to measure my battery. I'm testing my function from main and it works.
The procedure looks like this:
saadc init
sample data
saadc uninit...
I am using nrf52832 BLE chip(10040), sdk 12.2, softdevice s132 with sample example boot-loader code(dual bank).
I modified the boot-loader code for button-less DFU.
...
Hello,
I am using nrftoolbox code available here: github.com/.../IOS-nRF-Toolbox to perform the DFU procedure.
I have taken the firmware zip file.
I have integrated...
Is there a job board for Nordic developers? I'm offering a short contract job. I have a 100% complet e PCB design based on the Nordic chip. I'm looking for someone to write...
Hi.
I have a question.
I tested that nrf52 get datas from sensors.
But the code was not moved well,
I made code to test bit shift.
Please see my code.
#include <stdio...
I successfully built the example peripheral project "experimental_ble_app_queued_writes" from nRF5_SDK_12.0.0_12 and successfully downloaded the app to a nRF52832 development...
I have an arduino mega based design working with nrf24L01+ via SPI. As certification is the next step, I found a NRF52832 based module that would meet all certification requirements...
I've been trying to program a custom PCB with an nRF52832, using the nRF52 Development Kit and nRFgo Studio.
When I connect just the nRF52 Development Kit to my computer...
I'm an intern in my second year for a bachelor in computer engineering. I've been working with the nRF52832 development kit as part of my assignment. I was looking through...
Hi all,
I am experimenting with the DFU to switch between SDK versions from SDK12 to SDK13 and SDK13 to SDK12
Is it possible if I send a whole imagen of SD+BL+APP to...