Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
I combined ble_app_hrs of example with ble_app_hts of example .
I write command in client characteristic configuration,
there is a problem that ATT_ErrorRsp : status...
I have some problem with Interrupt vector,details as below.
I design a bootloader code,and in the bootloader,i use timer0 interrupt.Then in the app code,i use the timer0...
Hi all,
I was wondering if I can install Soft device for a BLE-module other than Nordic?
And if so, will it gonna work?
Thank for help in advance!
blueguy
Hello,
I would like to detect a change in a pin( GPIO_IN_NUMBER ) and depending on it I would like to trigger a SPI transaction, this should happen through PPI.
So far...
I'm trying to migrate my old app based on buttonless app sdk13 to buttonless app sdk14.
I solved issuie according to migrate guide remove chunk things and etc.
My app works...
I am creating an App for iOS using nrf beacon.
App is for garage door and i want to get notification when door closed or open, when beacon is in range or out from range but...
I am using nRF 52840 board. I used Keil 5 to load one of the examples in SDK successfully, but when I unplug the USB cable and used the battery. My program doesn't run properly...
We worked on the nrf52832 DK.
We will begin the prototyping phase. But the dev kit's antenna is too big. Can send me a reference and schematic of a ceramic antenna.
Other...
We have based our code off of ble_app_proximity. Upon first connecting to the advertising NRF51822AB device with softdevice 110 v8.0.0, we write to pstorage.
static void...
I USE IAR7.7 AND v11.0
THERE ARE ERRS.
FS_REGISTER_CFG(fs_config_t fs_config) =
{
.callback = fs_evt_handler, // Function for event callbacks.
.num_pages = NUM_PAGES...
SDK Version: 13 Alpha
I've been able to track down, through app_uart.h, where UART interrupt priorities are set using NVIC_SetPriority(). Now I'd like to know where interrupts...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello,
I am evaluating the USB audio example from SDK v14 with an nRF52840-Preview-DK (PCA10056, V0.9.2, 2017.25).
SW9 is set to VDD power, SW6 is set to DEFAULT. The...
Hi,
I'm trying to setup Keil with PC-Lint using Nordic SDK11. I've noticed that SDK files contain a lot of PC-Lint annotations and I assumed that it should work but I'm...
