For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
Currently we are exploring the features of BLE mesh to integrate this in upcoming project. In this architecture, we plan to use 2 Provisioner in the mesh and one of the provisioner...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
Hello,
I am trying to flash an application onto nRF8122 from an android mobile using the Nordic app. After pressing the DFU button, the programming fails giving a pop as...
I've been looking for information on GCC support for the DFU bootloader examples in SDK v7.2.0 for the BLE Dongle board(PCA10031) but unfortunately there's nothing in the...
Hi
I'm testing the nRF Toolbox for Android. But I get this error when I try to connect using the proximity feature:
I'm using the nrf51822 EK with the s110 ble_app_proximity...
Hi Nordic Guy,
I'm trying to fine tune my connection parameters for better battery life, while at the same time trying to keep them within Apple's guideline. I notice in...
Hello guys, I'm going to start programming for nRF51822 and I want to ask you something.
I'm going to start coding for mbed HRM1017 which is the simplest eval board I found...
I'm attempting to use a custom UUID as outlined in nAN-36. I get an error (NRF_ERROR_DATA_SIZE) when I call ble_advdata_set . Specifically:
ble_advdata.c::uuid_list_encode...
I have a bluetooth hub (NRF51) as central and a wearable device (NRF51) as peripheral. What I need is that as soon as a smartphone enters the range the peripheral let's go...
Hello,
I'm redrawing and routing my own PCB for nRF81x22. I take the details from pca10028 files.
My question: Can I route the PCB with only 2 layers?? I have seen only...
Hello,
I had to use sd_ble_gap_address_set() to make sure, that a bootloader running on the same device will not be cached on OS/X:
static const ble_gap_addr_t gap_addr...
This may be a newbie question, but it had puzzled me for a while now.
Looking at the PCA10031's schematics i can see two leds been used.
LD2 i can figure out. Datasheet...
MQTT Example in the IoT SDK compiles with size bigger than available 160KB Program space?!! Is this correct as I can't flash with the IoT SoftDevice on it.
The drive level of the nRF51822 is specified as 1µW, whereas the EPSON crystal suggested in the BOM for the EK boards PCA10000 and PCA10001 is specified for just 0.5µW (with...
hi nordic
i just got a little bit outdated "nRF51422-dk" package. I have problems with flashing
the boards pca10006 and pca10007- I tried to search for an solution, tried...
