i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
As per the steps given to program bootloader to the device i have programed it.
But the code is not getting executed i.e advertising nor led initilization is taking place...
Hello im trying to connect to a slave on BLE_GAP_EVT_DISCONNECTED event.
Can i use sd_ble_gap_connect(...) on this state, im getting error code 0x3202.?
regards, Vo...
Hi, I have bought the nRF51 development kit. I have downloaded source code for nRF51822. This comes with LOTS of examples but I suspect the codes are not for my board. Is...
I'm manually creating the .dat file for a DFU following the format specified in this document .
Where can I get the device type and revision values from to populate those...
I have bought the nRF51 dev kit. I can download all these soft devices. But what do they really correspond to ?
I think of them as library/apis for doing BLE development...
Hi,
I am trying to run the ble_app_hrs on my nrf51822 based board in combination with the nRF51822 Development Dongle. I am following the instructions from nRF51822 Development...
How can I add PKT_TYPE_INIT (DFU Contorl Point - OpCode = 2) into my DFU?
S110 nrf51_sdk_v6_1_0_b2ec2e6
Chip nrf51822
Softdevice s110_nrf51822_7.0.0_softdevice.hex...
I have a nRF51822 chip sending me BLE UART data to my phone and it works fine with the app. No I want to send it to my PC and Read the data (and send commands) via PuTTY....
Hey guys, I'm looking for a printed antenna PCB file. I have already read the white paper and I think using a more complex antenna would save more space and increases the...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
MCP and iOS are generating a different event sequences for a long writes.
MCP: after the BLE_EVT_USER_MEM_REQUEST...
Hey, I noticed that most of the wearable ble devices (without keyboard and screen) on the market are using 'push to confirm connection' authentication, when you have to push...
Chip nrf51822
S110 nrf51_sdk_v6_1_0_b2ec2e6
Softdevice s110_nrf51822_7.0.0_softdevice.hex
I use "nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\pub\device_firmware_updates...
Hi,
I am trying to set up a custom service and I have it all setup and it works properly. The only problem is that it is advertising as a 16bit service. I am moving from...
Take into account an application on the nRF51822 and S110.
I have defined different custom services, so UUID is 128bit long.
When advertising:
Is it advisable to include...
