Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi,I have some problems in debug with experimental_ble_app_buttomless_dfu project.
First i build the experimental_ble_app_buttomless_dfu project,so i get the app_buttomless...
We am improvising nrf blinky application, we have got stuck in a problem, after button is pressed from nrf52-dk code goes into forever loop and after a while connection is...
I have two nrf51822 modules and first one is sdk8.0.0 / s110 / peripheral device, second one is sdk10.0.0 / s130 / central device. I've sent a 10-character data array like...
Using:
SDK14
Softdevice132 V5.00
app_uart driver with legacy, no easy dma.
UART is set up with hardware flow control.
The pins should be set up correctly: rx-tx , cts...
i want to konw ble evt struct 's content of meannig . i want to find what's the return value when packet send fail and what is the channel id different from other ruturn value...
Hello,
I want to falsh nrf51422 device. I ma developing software using Eclipse and SDK_7.2.0.
The soft device is 130. I have build the project successfully and Hex/elf...
Hi
I'm trying to communicate between nrf51-DK and arduino using twi. I was able to send data from nrf51-DK to arduino using nrf_drv_twi_tx but when I'm trying to send the...
Reference PWM_driver sample code,
I set the customer status of the LED,
And it also can change status by button,
static void bsp_evt_handler(bsp_event_t evt)
{
void...
Hi,
I want sample code for configuring baud rate of UART from mobile application (nRF Connect). So I don't need to hard-code the baud rate in my program.
Please share...
With version v2.0 of S332, I checked for a return of BLE_ERROR_NO_TX_PACKET when using the ble_nus_string_send function. I use this test in a routine which writes buffers...
I called these command:
nrfjprog -f NRF52 --eraseuicr
nrfjprog -f NRF52 --program app.hex --sectorerase
During the eraseuicr I see:
Erasing UICR flash area.
Applying...
Hi there,
for my Application, I want to listen for all BLE packets on a fixed channel.
No SoftDevice is used.
I receive all packets as long as BASE0/1 and PREFIX0/1 and...
now, i have a question: i have a buffer 100byte data to send, when i send data package via sd_ble_hvx() continus,delay 20ms after each send ,but it will lost some data , i...
HEllo,
I am facing and issue with undefined references for the linker. The compiler is able to compile, but I get linker errors like these
.../pca10040/s132/arm4...
Hello everyone, I recently use the nRF51822 with SD9 and S110, I found that the device name was define as: #define BLE_GAP_DEVNAME_MAX_LEN 31
is it means the max length of...
