Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
After reading some older threads it seems to me that someday it must have been possible to update bootloader and application with one zip file.
Currently I'm using sd 132...
This is kind of a follow-on to the original question here: devzone.nordicsemi.com/.../
I notice that the nRF52840 PDK dev boards need to be closer at the beginning of the...
Hi!
I am sending the battery status every 1sec from nRF52840 peripheral device and receiving it on nRF5240 central device. (verified the battery status working through...
Hi,
I am unable to read values from ADC pins, usiing nrf51822 nordic bt module, s130 softdevice.
Things I dont know:
Connecting to ADC pins
readings from the pins...
Hi,
If I set the tx buffer to 0 before and transaction, I expect the spi slave register's AMOUNTTX to be 0 when the transfer complete. But intstead, the AMOUNTTX always...
I'm working with a sensor that communicates over spi, but it uses a single wire for miso and miso. Is there any alternative to just bitbaning the protocol? Specific sensor...
Hello.
we are using the nrf51822 and doing the approval of the radio transmitting equipment model.They refer the modulation mode,as the picture:
I am asking:1、can the modulation...
I'm working on a central device. I'm using 52832, SDK11, SD2.0.0
I accidentally used a peripheral device that doesn't have the right service UUID that my central device...
I'm using nrf_delay_ms to trigger a series of beeps though a speaker using PWM, but I seem to have intermittent problems with this when the device is connected.
Basically...
I am trying to get fstorage to work, but I seem to miss some of the symbols needed: "error: 'NRF_EVT_FLASH_OPERATION_SUCCESS' undeclared". These are declared in softdevice...
Hi all,
I am using a BLE nano 2, which is based on the nRF52832. I am trying to measure small capacities of a few pF with this method:
wordpress.codewrite.co.uk/.../...
I want to connect a central and peripheral and only have ble on when the peripheral senses a certain event that exceeds a threshold. Do the devices need to connect on startup...
Hi Nordic,
I’m H/W engineer, dedicated in development of radio circuit. I ask the question because we’d like propose your Nordice nRF52840 to our customer when replying...
I am developing an application which uses 2 nrf52 running sdk 12.3 and softdevice 132 V3.
The central device appears to be saving and whitelisting the two peers, but it...
Hello!
We designed and manufactured board with nRF52832_QFAA. The NFC pins was configured as IO and connected to sensors. The problem is that we see that those pins get...
