Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I see the python S110 bindings (via SWIG) have been made; it was pretty easy to get the demo code up and running, many thanks! Any chance that S120 central role bindings can...
I have a custom board with an nrf51822 device. I also have Keil 5.12 and a ULINK2 and would like to program softdevice hex file into the nrf device. I have followed all of...
I'm trying my best to get started w/ the nrfgo 51822 development kit that I got last summer, but I'm just having a hard time jumping in.
I was a little disappointed to...
I need to use a high speed PWM (> 500 kHz) in which I can vary the pulse width. In examples, it's handled in software which is too slow.
Is there any way to set a pin on...
Hi,
I am having some problems getting the s110 SoftDevice working (sd_softdevice_enable stops the program execution) on a custom PCB. I have seen several issues similar...
Hello,
I Preparing the KC (korea-certification. about bluetooth)
KC requirements as follows:
Set Test Modes
Set Continuous modulation mode
Set Unmodulated...
I'm interested in getting started with NRF51, but the full DK is quite expensive here and I don't need it. Does the nRF51-Dongle sku come with a key for downloading & using...
Hi,
Can someone tell me (definitively) what the max SPI clock speed is?
I have seen 2,4 and 8Mhz here and in recent documentation and I'm confused.
Thanks
Hi
I have been experimenting with encryption and bonding and I think I don't understand completely the bond procedure.
To bond a device, it is necessary using the bond...
HI ,all !
I have a question about PORT event function.
as the 4 channels of GPIOTE (channel0 to channel3 ) have been used for other usage.
i need to use a general IO...
The only documentation I can find for s120 is part of the nRF51 SDK . Though it isn't clearly stated the SDK assumes release 1.0.1 of S120 is being used.
The v2.0.0 S120...
Hi
I got some questions about KEIL MDK uVision5.12 PACK.
I tried uVision5.12 PACK to install Nordic SDK package. Currenly, their latest version is v7.1.0.
If...
Hi,
I get 0x2001 error in spi_master_close() at the following 2 lines.
/* Disable interrupt */
APP_ERROR_CHECK(sd_nvic_ClearPendingIRQ(p_spi_instance->irq_type));
...
I got my UART working just in basic sending and receiving.
Now I am trying to implement buffer feature and other non-blocking features. I have done this on other CPU's many...
