Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi everyone,
I am using nRF52832 chip and trying to use BLE on that. I flashed SoftDevice. When I flash the "ble_app_uart" example, error code 0x3001 occurs. the function...
I am using jlink to program the custom board. I was able to program the board earlier, but now this error is comming. I have rechecked the connection and it is fine.
The...
Hello all,
I am in the design stage of custom board for Automotive application using nrf51824. i have the below queries,
In the below link there are two reference...
If the DCDC is enabled in the nRF52832 and during operation one or both the external inductors is damaged what is the effect on the device? Will the power sub-system compensate...
Hi,
I can send and receive commands from nRF51 Dongle to nRF51822 via using nRF Connect UART over BLE Service.
My question is : Is there another way to reach nRF51 Dongle...
Hello,
I have chip nrf51822 connected to nrf51dk. An usb connection provides power to both chips. While checking power of both chips via nrf connect on iphone7 i discovered...
Connect establish with smartfone in peripherial mode. SDK13. S132. Periodic I observe disconnect, than 2-3 advertise packet and new connect again.
Where can I see what reason...
I have a little hobby project going on where I'm trying to make Nordic's old temperature broadcaster example work with the nRF52: github.com/.../
The project was originally...
As the product specification says,The HFCLK clock controller provides mang kinds clock to the system:
HCLK64M:64MHZ CPU clock
PCLK1M:1MHZ peripheral clock
PCLK16M:16MHZ...
Hello Folks,
I am currently try to program RedBear BLE nano board (which is essentially nrf51822) using Nordic SDK v12, which has features of secure OTA. However after...
I have started working on the external file access with NRF
is it possible to read or access the data from the external file into NRF programming
similar to what we do...
I am running a modified version of the app_uart_c example on a nRF52832 using softdevice 132.
I want to send a large hex number to the peripheral I'm connected to. Is it...
Hi,
No matter what I adjust, I can't get the PPK to output over 2.2V. I happen to be using an older nRF52 preview DK (figured it'd be a good use for that board now that it...
tl;dr: UART transmission sometimes stops and never resumes. Only a
power cycle resolves the issue; a system reset is not sufficient. The
problem only occurs when flow control...
