در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hello iam using softdevice 110 and SDK 10.0.0, I have created project using ble_app_uart example code, i have added device manager APIs to manage bonding. Problem is iam GATT...
Basically, it can be divided into two cases
Reading/sampling TX pin of the sensor (since usually nothing is sended back)
Send/Read possibility - in case of range switching...
Hi all, today I was working properly and, in a second my nRF52382 (I use SD s132 V3.0 without bootloader, and SDK 12.2) is "disappeared". I googled and I've found some cases...
I am using nrf51822 with 16k RAM chip, xAA.
I followed the procedures...but I don't know what is wrong with it..
Program secure bootloader with S130 (2.0.0), SDK...
Hello,
I am trying to use the new nRF Connect 2 for Desktop. After installation, the app gets stuck and doesn't show any GUI. Investigating the network shows that the app...
I have been setting up systems to develop nRF52 code for the better part of two years. Maybe I am getting forgetful in my old age, but I can't seem to get it working this...
Hi.
I am looking for appropriate 2.4Ghz Nordic RF chipset.
I have studied 2.4Ghz chipset. but so clearly show about
1:n audio streaming (mono or studio)
exactly what we...
Hi, we are using nrf51822 xxAB based module and would like to understand which SD/SDK combination is best to use in terms of memory usage. We have developed original firmware...
I'm in the process of migrating from SDK11 to SDK13. I have a custom UUID with 3 characteristics (2 notify chars for data and 1 r/w for sending commands), based off HRS and...
Using SDK 12.1.0
I2C with SoftDevice works on PCA10040 Eval Board with nRF52832 but
hangs in the nrf_drv_twi_enable function with TY module EBSGCNZWY which is an
nRF51822...
Attached program has 4 characteristics
UUID_VLEN1 - VLOC_STACK, no rd_auth or wr_auth - value can be read after written
UUID_VLEN2 - VLOC_USER, no rd_auth...
Hi guys,
I'm receiving the following errors whilst trying to setup to the Crypto library on nRF52:
............\components\libraries\svc\nrf_svc_function.h(72): error...
#problem
Not work ble sample code with s130 softdevice on nrf51822 module.
I just want to advertise by sample code.LED test with s130 is work well.
#Environment
...
Hi,
when looking at nrf_drv_i2s.c in SDK v13.0.0, the description of nrf_drv_i2s_start() states that the parameter buffer_size is Size of the buffers (in 32-bit words)...
