I would like to implement ble mesh direct forwarding feature in my code but i am not finding zephyr library for that. Is there any possibility to get link for zephyr direct...
Hello,
I am working with the DWM3001CDK (nRF52833 + DW3110) using SDK 17.1.0 . I have successfully compiled and flashed the DTM example.
I am trying to use nRF Connect...
this is my prj conf
# Bluetooth
CONFIG_BT =y
CONFIG_BT_BROADCASTER =y
CONFIG_BT_OBSERVER =n
CONFIG_BT_PERIPHERAL =y
CONFIG_BT_DEVICE_NAME = "Range extender"...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
I understand part of ram is used by the softdevice, but I see different addresses are used in different examples that use the same softdevice, namely S132. For example,
...
I am trying to run the examples given by Nordic on my nRF51 dongle. Most the examples are for PCA10028 or PCA10040 where as my dongle is PCA10031. I tried running them but...
Hi,
I need 6 PWM channels for a BLE project. Is there any solution to add 2 other pwm channels to nRF51822? If not, Which other Nordic ICs might be helpful instead?
Thank...
Hello,
I am using SDK 12.01 with softdevice (BLE application) and I want to write large data over flash. I am stuck with various issues.
When I try to write the data...
Hi,
I am having hard times to make SAADC working on DK-52, SDK13, S132. I need to perform a voltage measurement on command received from a connected device.
AIN pin...
Hi All
I am looking for the way to send and receive the string between nrf52 and mobile app.
what are the possible ways to do with minimum power consumption.
main concern...
Hi,
I've allready read a lot about using a static passkey on the DevZone and I have tried tons of things, but I just can't get it to work.
What I want is to connect...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi, I am playing with the SDK13 examples, UART (w/o softdevice). I use gnu gcc. The example runs and when I type q or Q the code goes to the printf(" \r\nExit!\r\n") as designed...
Hi
I read somewhere that when using internel ref for analog measurements the Vin changing does not influences the analog reading. Is that true?
Please, consider the circuit...
Hello,
I am looking through the data sheet for the NRF52 and do not see anything for writing to NVMC.
I see you can erase and configure the NVMC using:
NRF_NVMC ...
Hello, i'm using a microcontroller connected to a nrf24l01p in rx mode,after receiving a packet it writes the ack for the next transaction,it only works if i add a delay ...
hi i am unable to find cause of issue i am working on BLE and PWM driver when i get data in nus_data_handler i am calling pwm init function. and then it is going to
ble_advertising_on_ble_evt...
