Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I'm looking at using an nRF51822 in a Gazell or ESB application. I prefer not to have any softdevice loaded at all.
What is the correct procedure to perform clock calibration...
Hi
So far I have been using the examples from Keil 5 pack installer.
Now I tried loading some from the SDK example folder and I have issues with includes.
What do I need...
I included button less DFU service in the proximity profile example.When i compile i am getting the following error.
..\..\..\..\..\..\components\libraries\bootloader\dfu...
Hello,
I am working with the example "experimental ble app cgms" in SDK 13.0 and using nRF52832 DK.
when a connection was settup and pairing completed, the CGMS sensor...
I want to ask general question about antenna designing as I am designing antenna to be used with NRF52.
The picture attached with this message shows a printed antenna coil...
At the moment I'm sending a notificaties during the BLE_GAP_EVT_CONNECTED event. This sometimes results in various errors but I can take care of those. The issue I'm having...
GerberVINR-178.zip
SchematicVINR-178.pdf
Bottom layer
Top Layer
IC on the PCB is marked as follows: nrf51822 QFAAHO 1627WM.
I am able to program the custom...
Hello,
I want to create BLE connection between two different modules - nrf51822 and TI CC2564 (possibly Laird BT800). Is there any chance on using Gazell protocol on other...
Hi,
if I got it right, the Radio Timeslot API is not supported by the S140 softdevice. Is this right? Why is this and are there any plans to support the API in later versions...
HI, every one, I joined the watchdog program in application,i use sdk11.0, and i found the problem that when i download the program , the MDK compiler point out "error: flash...
Hi,
I am doing development on Android platform. I am using Marshmallow device to develop my BLE application. Many times I am getting status code 129 in onServicesDiscovered...
Hi, i'm working on a custom board with microswitch (Crouzet V4) in order to get the position of a moving part inside a machine. This switch is in pullup mode with a 100k resistor...
Hello,
I am using nrf51 and sdk12.2. I want to print data to terminal using printf function. So I added app_uart_fifo.c also I included paths. I did not get any errors from...
I'm using NRF51422, s130, SDK v12.
And I'm working on a project that can connect concurrent peripheral and Central.
In this continuious connect and disconnect sequences...
