Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I'm using nrf51822 and ble_app_uart in SDK12.3.
Testing with android app nRF UART v2.0
I have some problem with BLE connection.
First, Sometimes when I tried...
Dear Nordic:
I have transplanted my code from sdk 10.0(nrf51422+S310) to sdk 13.1(nrf52832 + s332(v4.0.2)).
I program softdevice and application to my board by nRFgo_Studio...
I just tried to add a custom service, so I expanded my ble_cfg.gatts_cfg.attr_tab_size.attr_tab_size. Now, when I call sd_ble_cfg_set(BLE_GATTS_CFG_ATTR_TAB_SIZE, &ble_cfg...
Hi everyone,
For my project I'm currently using the sdk 10.0.0 (S310 on a nRF51422) and I would like to use the Secure DFU provide by the sdk 12.0.x.
Working on a nRF51422...
Hi everyone
We have a custom made board with NRF52832 chip. We are send it to FCC test lab and they told us the occupied bandwidth (OBW) is too small, 940kHz less than...
Hello,
has anyone tried new v1.1.0 for nRF6707? If I change the window size to more than original 2.0s, GUI becomes very laggy and it is very hard to stop the recording ...
Hello,
I've been trying to test DFU over UART which has been added in SDK13.1 but after following every resource I've found I always end up with DFU not working
The...
I found this question which partially answered what I am looking for:
devzone.nordicsemi.com/.../
Essentially, if I am creating a new project with my main.c file and...
Hi I am trying to design a custom BLE board using NRF52832 by following the reference layout.
I am new to RF design and I have got a few questions that I would really appreciate...
Hi
I'm trying to implement DFU in my project. So far, after I sending 01-04 to the control point characteristic(1531)，I can get bootloader signal, to be exactly, i can enter...
Hi,
Can we interface a smbus based sensor with NRF51 or NRF52? The only difference between smbus and TWI is the minimum speed requirement which is 10Khz if I am correct...
Dearl all,
I want use the eclipse and gcc together to program the board nRF52840 Preview DK. I was following the tutorial devzone.nordicsemi.com/.../.
I followed the...
Hi,
I'm using nRF52832 with sdk 13.0.0(softdevice 4.0.2).
I had trouble to connect nRF52 and some android 7.0(or upper version) smart device.
I tested samsung galaxy tap...
Hi All,
I am trying to get the serial DFU working with nRF52832 development kit with SDK 13. I am able to get the bootloader flashed and have installed the nrfUtil tool...
