Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
I was able to measure current with the test probes I have. However, I really liked the idea of test probes that were like the ones in the drawing below. I have not seen test...
I am using the PWM library in this repository for a nRF51822. I write the following code to generate a ~ 30% dutycycle 500 kHz PWM output:
#define V_CLK 5
static void...
Hello,
I am using Timer_2 with two CC registers configured, 2 PPI channels (one for each CC register in the timer), and one GPTIO_TE to make a PWM to control dimming on...
hi,
my nrf51822dk was downloaded s110 hrs demo,and it was advertising,i used a ble sniffer dongle to get the advertising data.the AdvData is "0B 09 4E 6F 72 64 69 63 5F 48...
Why is it a standard in nordic-supplied code to initialize structs with memset like so? An example would be:
ble_gatts_char_md_t char_md;
memset(&char_md, 0, sizeof(char_md...
//Edit:
So Hung Bui just told me in another question, that there is indeed a buffer of size 6 or so?
How can I decrease that to 1 (i.e. disable it) so that only the latest...
I have the nRF52 DK and cannot determine the silicon revision on it. Is it the 'Engineering A' revision and therefore is subject to all the Errata that is currently published...
there are 3 modules to test(A1,B1,C1)
*2. A1 connect with B1(B1 is master, A1 is slave), C1 is power off, B1 as slave attempt to connect C1 with BLE_GAP_ADV_TYPE_ADV_IND...
I need a PWM signal as outoput from the nRF51-DK. And I do need the softdevice. So I decided to pick the code from the nrf51-pwm-library-master and add it to my project(SKD...
Why I will restart the ADC is used to measure the voltage is greater than 1.2 V
void battery_start(void)
{
uint32_t err_code;
// Configure ADC
NRF_ADC->INTENSET...
I just assembled my first nRF51822 board and I was able to program it using an IDAP-LINK and a blinky program compiled with the Eclipse/GCC toolchain flashed via SWDIO/SWDCLK...
