I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
hello Nordics,
i am trying to configure 1ms timer along with BLE_STACK is enable
and same time i am sending 3byte data for every 500ms . and 1ms timer is very important...
I need to automate OTA updating the bootloader and radio for several hundred units that have an nRF51 (softdevice 7.1.0) from a VB.NET windows application. I'm able to call...
Hi, I just bough a couple of dongles (nRF51422_xxAA, with 16kB RAM afaik). In Pack installer there is a lot of example for the nRF51 series but all of them are for nRF51522_xxAC...
Hi,
I have a scenario where we may want a peripheral (using S110 softdevice) to switch connections between 2 centrals, depending on whether the centrals are present or...
Hi,
I am using the sofdevice s110. I want to encrypt my manufacturer_data. However , the type of the advertising is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND.
I tried : nrf_ecb_init...
Hi,
I use an NRF51822 eval board.
Recently i buy a module RFD22301. But it is programmed to be used with RFduino.
How I can program it to use the nordic Nrf51822 basic...
hi!,
I am configuring connection interval time is 7.5ms ,
and slave latency is zero.and every connection interval event I am sending 1 packets (and my data lenth is only...
I'm new to nordic. I am using Nordic DK (PCA 10028) and was able to flash the heart rate example on to the board and see it on my iOS device. I'm trying to test the uart sample...
I'm trying to install nordic SDK for Keil 5.13, but this is what the 'install.bat' says when I open it inside the directory containing 'PackInstaller.exe':
Please wait...
Hello,
I am interested in "nRF51 Smart Remote 2". As I have read in Product Brief it supports feature "Voice Command Features". But I couldn't find any information about...
Hello,
I have an application in which the available power is so extremely limited that the hardware cannot do anything else at the same time as conencting to a central...
Hello All,
I am not an electronics engineer and have less experience with hardware. Posting here on behalf of my design engineer for help
In our nRF51822 based device...
Dear Nordic support team,
Could you give some rough estimates for availability of production-ready version of the S130 soft device?
Thank you and with best regards,...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
