For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
Currently we are exploring the features of BLE mesh to integrate this in upcoming project. In this architecture, we plan to use 2 Provisioner in the mesh and one of the provisioner...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
Hello,
I am having some trouble properly using UART and my MPU-sensor on a nRF52832-custom-board.
The UART-pins I am trying to use are P0.05 for UART_TX and P0.06 for...
Hi!
For my master's dissertation I am currently investigating the possibilities of Bluetooth Low energy in terms of speed. I am using the Nordic UART service to send as...
Hi, I use PCA10040 v1.1 with Keil MDK 5.20 and SDK 12. I have installed J-Link 5.12f driver.
I usually use the NRF_LOG_ENABLED MACRO to check the UART debug message.
...
Sorry that I'm asking 2 questions in one go, but they are closely related.
Problem: got 0x00000008, INVALID_STATE error when calling sd_ble_gatts_hvx, looked it up, it...
Hi,
Tried to use nrfjprog to erase / program the nRF 51 DK, when running nrfjprog --version, it yields the error of "JLinkARM.dll not found. Please reinstall latest JLinkARM...
Hi,
I start the sniffer (on Windows), wait for it to find an advertising device, select that device, and then start Wireshark 1.12.8 .
In Wireshark I can only see broadcasts...
Hi,
For some time, I've been developing code on the nRF51 with a U-lInk based debuggers and Keil. Things have worked well with that setup. One particularly nice feature ...
Hi,
I see some issues when I use HW whitelist with random address type.
What I do is:
set address in DAB[] and DAP[] register
set DACNF to 0x0101 (ENA0 and...
i want to connect nrf51822 with android phone via bluetooth. can you tell me which code i have to burn from sdk of nrf into the nrf51822.what are the requirements for making...
Is there a way to configure AAR so it can do address match for extended advertising packets?
For legacy we had to:
put address into DAB[] and DAP[] registers
set...
Hello everybody!
Feel free to read this question for more background information:
devzone.nordicsemi.com/.../
I'll give everyone reading this a quick bulletin run...
Hello all,
I am newly started working on nrf840 device and i am getting the error like "flash download failed-could not load the file" please help me out to over come this...
Hi, I'm developing a new device using the nRF52832, I have finished the schematics design and I'm wondering how can I simulate the design to check if there is any mistakes...
Hi all,
I am using SDK13 with NRF52DK. I am trying to get NFC to work with a reader and encountered some problems.
I have tried 3 different examples, record_text, writable_ndef_msg...
