Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
There is a following initialization in 51822:
static void controls_init(void){
uint32_t err_code;
// Configure pins.
uint32_t pins_transition_mask = (1 << SCKIN_PIN...
I'm working on a project using the nRF51822 beacon kit (PCA20006), and I've downloaded the firmware files installer from the website. After running the installer, I can see...
Hello,
I have a ptr5518 module which has nRF51822 in it. I need help programming the device. I am new here so a detailed help will be very useful.
I want to use the built...
Hi,
I'm workin with nRF51822 as peripheral device. is it possible to retrieve the device name of the central at the moment of the conection i mean when is generated the BLE_GAP_EVT_CONNECTED...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.6.0.8331
When the line wrtHandle = hdr->Handle; executes I get an Hardfault Error. Why?
case BLE_GATTS_EVT_WRITE...
Hiii, i work on PCA10028 nrf dev kit and i want to made code that receive data from mobile to UC and go back to mobile. is anybody have this code than please give me and also...
Hello!
Looking around and reading a bunch of posts, I found little information on how to initialize the TWI sw frequency, which currently is 100 kHz( calculated it with...
I want to operate
Tries to operate a small speaker.
www.wvshare.com/.../Analog-Test-Board.htm
but I can not find the DAC function in nrf51822.
How do I create...
Hello,
I am starting a project related with BLE communications. In the future, I want to design my own board and to be able to program it. I am going to start with a development...
Hi, all.
I have been using the nRF51822 board, I am making a peripheral.
The peripheral has been equipped with a sensor to multiple GPIO.
(For example, sensor1 to P0...
Hi
I am implementing my custom service, and started from the led/button example.
I am using the LightBlue app on my iphone to connect to my device under test.
I can see...
I am trying to generate the services.h file and get an error that "Something was wrong with the advertising packet". I see at the end of the log it says "Return code: 0x2...
Hello All,
I have a basic question about empty scan response operation with the ADV_IND PDU. When I set advertising data as follows:
err_code = ble_advdata_set(&advdata...
