I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
We are working with the nRF7002-DK board and need to measure and minimize power consumption. We are using Wi-Fi in our application and currently working with the sample nrf...
I thought I had been extremely careful to _not_ brick the device, but apparently I did.
I created a firmware-dfu.zip file, even with appropriate keys, etc. as below.
...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
Hello,
I am using configUSE_TICKLESS_IDLE with RTC2 setup for FreeRTOS tick, occasionally I am seeing the asserting in task.c at line configASSERT( ( xTickCount + xTicksToJump...
Hi,
I have a question about creating a custom board. I am following the tutorial here: youtube
I am trying to make a custom board for nRF54L15 using the board wizard ...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hello everyone.
WE're trying to make a https connection with google.com and execute a GET request.
Wifi connection is working; DHCP seems to be working (my personal assumption...
HI DevZone,
I am trying to add the coded phy features in Peripheral_Uart and Central_Uart examples of NCS. I hope Coded phy features are successfully added into Peripheral_Uart...
I was able to complie many of the nrfx/samples under SDK v2.5.0 using VS Code IDE but cannot successfully compile any under SDK v3.0.0 .
The [Building and running]: <.....
I have a application where I need to time acurately the time between two enternal pin signals. I have this working using the
k_timer which & read & restart within the...
nRF52810 will not enter deep sleep (system level power management). The method used is through pm_policy_next_state, sleep entry function , sleep exit function, and PM notifier...
Hi,
I found that the NRF 54l15 can only estimate distance based on channel sounding and RSSI. On the bluetooth website it mentioned channel sounding accuracy being around...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration:
CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
