I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I am new to nRF 52. Previously i have worked on arduino IDE for programming arduino uno,mega. I have also used MPlabX for programming PIC(MircoChip) series micro-controllers...
Hi,
For the NRF52832, I read that a number of write (per block) is limited before a forced erase of the page. Apparently, the amount of write is 181 times for a block of...
My sensor app is based on nRF UART service and my current case in one sensor (peripheral) one gateway (central).
In a situation where there are two pairs of sensors (S1...
I'm trying to use a low accuracy GPIOTE event to start RTC1. The following code works as expected when using hi accuracy mode but will constantly trigger in_pin_handler()...
Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. mainc.txt
Even after allocating the access address of Bluetooth on line 196 as set_address0...
Using nRF52832 I am collecting from 8 SAADC channels using example ble_app_uart__saadc_timer_driven__scan_mode as a guide. AIN3 (P0.05) gives incorrect results. Because P0...
Hi,
I have an application that utilizes the dual bank bootloader and s132 soft device on the nRF52832 chip. I am trying to determine the total RAM used and can't seem to...
Hi,
i am using NRF52 and S132V2.0.0 SDK11. i am working on BLE application in which i implemented DFU service to it, so that i am able to observe DFU service and 3 characteristics...
Hi
I use SDK version 12.2.0 to do a project. I add two 128bit uuid into my project. The one of 128bit uuid is created by myself. The other one of 128bit uuid is used ancs...
Hello,
I wanted to check the log on nRF52 example codes. Though the code compiles and runs (GCC compiler) I do not see the log anywhere. I tried connecting the device ...
Hello,
I was going through the schematic of PCA10040 and I see that the nRF52832 is interfaced to an ATSAM3U2CA-AU. I was under an assumption that nRF52832 itself is a...
We have a custom PCB with the nRF52 MCU.
Our application uses BLE. Thus, we need to program first the SoftDevice. In our case, we are using nRFgo Studio.
Normally, when...
Sorry to ask again, but even after looking for some time at all the marketing material and the forums, it was hard for me to find out what BT 5 features are really supported...
Hi,
I followed the RTT tutorial but When I try to BUILD the project I got this error. What is it?
Error: L6200E: Symbol SEGGER_RTT_WaitKey multiply defined (by segger_rtt_1...
