I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi community,
I'm working on a BLE gamepad with custom board based on 51802 and s130, code modified from ble_app_hids_keyboard . The gamepad works like a charm on my Android...
Hi, Nordic!
We have two PDK-NRF52840 and custom boards with NRF52840 chips.
2 from 5 chips have a broken bit in RAM. This is different places.
For example:
Is this...
Hi all,
if i buy 2 nrf52840dk:
Is possible create an audio connection like intercom between the two dk?
Can I send my voice from "dev board 1" to "dev board 2"?! and...
Hi,
I beginning now to program nrf51822. I would like to let the nrf51822 wake up after 3 hours by using a software timer interrupt.
Should I use power_manage()? Before...
Hi,
I'm trying to configure custom local GATT server on nRF8001 device. I added a custom service with multiple characteristics, but I can't generate source files. It says...
Hello!
I'm doing master thesis and I've chosen WT51822-S4AT board for BLE. I've made board successfully and programmed uC to send serial data to BLE.
I'm able to received...
Hi all,
I am using nRF52832 DK for my project. I need to config BLE for connecting with my phone. After a lot searching, I know that I can use softdevice API for configuring...
I mashed up RTC and SAADC examples. The files of the project are attached in the end of the post. The problem is that after the first iteration (I want to sample audio for...
Hello,
I am using developping on an nRF51822 with SDK12. In our application, our custom board need to communicate with a computer through a USB communication. I am not...
I'm working on the product using the nRF51422 QFAAE00 , SD110_nrf51_8.0.0, SDK 10.0.0. My product has the advertising flow as below
The device advertises forever...
Hello!
I have a problem when scanning and advertising at the same time with a NRF51822 and S130 v.2.0.0. (SDK11).
I can start both scanning and advertising without any...
Hello,
I am designing a PCB layout using nRF52832, I want to make it as small as possible so I am considering to route all component tracks to another layer.
I want...
Hi,
For an application I have a nRF51 at my disposal and I need to transfer about 3'000Bytes. I found in the documentation that the nRF51 can use the S130 SoftDevice which...
Hi.
Using PCApp/MCP(v 3.10.0.14), How can "BLE_GAP_EVT_SEC_INFO_REQUEST" occur?
Or will not it occur?
If it occurs, please tell me how to do it.
Thank.
