Hi everyone,
We're reading BAT level by reading data from ADC pin and the setup diagram is shown below.
We tested our device at hospital, and we observed significant...
I want to have two Kconfig flags that are both booleans but the build will fail if both are set. My code below used to work in pre ncs3.0, I'm wondering if there's a better...
Context:
VS Code
NCS 2.9
nRF54l15 custom board
Mac OS Sequoia15.5
peripheral_lbs sample project
Goal:
The goal of this project is to create a bluetooth beacon...
Why project config is not finding relative path of these files but absolute path works fine:
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip-DAC-Cert.der" ...
Hi!
We use nRF Cloud Log backend in our project. And during my research I found that it actually doesn't filter (despite the filtering code is there) messages generated...
I am looking for a solution where I can set custom and configurable root Kconfig file via Cmake cache variable, which can be specified through the west build command.
Steps...
I'm working on an Android app that connects to a Nordic nRF52833 BLE peripheral (Zephyr 3.7.99 / NCS 2.9.0). I'm encountering a consistent issue where:
The app connects...
Hi,
1- Many MCUs, including NRF9E5, have specialized communication ports like UART or SPI. Why not I2C? I assume that every pin can be programmed for any communication...
Hello,
I reckon that it is not possible to write application logic that decides whether to answer a connectable advertisement packet with a connection request as soon as...
I am using the nrf51822 with sdk (6.1.0) and s110 (7.1.0).
Can I do this?
If the nrf51822 is advertising, do Smartphone search the nrf51822?
Or do the ads on My smartphone...
Hello,
In the following code, I have tried to assign a channel to be asychronous so that I can transmit 8 byte acknowledged messages immediately following a button press...
Hi Support team,
I've ported succesfully chibios RTOS on the nrf51422 for month. I've also ported some drivers like I2C - UART - SPI- GPIOS and others... I can play with...
Hi, I have the nrf6310 code in C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\nrf6310\s110 and then i need use this code in the board PCA20006 (Smart beacon).
Do you know how...
hello Nordics,
i am trying to configure 1ms timer along with BLE_STACK is enable
and same time i am sending 3byte data for every 500ms . and 1ms timer is very important...
I need to automate OTA updating the bootloader and radio for several hundred units that have an nRF51 (softdevice 7.1.0) from a VB.NET windows application. I'm able to call...
Hi, I just bough a couple of dongles (nRF51422_xxAA, with 16kB RAM afaik). In Pack installer there is a lot of example for the nRF51 series but all of them are for nRF51522_xxAC...
Hi,
I have a scenario where we may want a peripheral (using S110 softdevice) to switch connections between 2 centrals, depending on whether the centrals are present or...
Hi,
I am using the sofdevice s110. I want to encrypt my manufacturer_data. However , the type of the advertising is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND.
I tried : nrf_ecb_init...
Hi,
I use an NRF51822 eval board.
Recently i buy a module RFD22301. But it is programmed to be used with RFduino.
How I can program it to use the nordic Nrf51822 basic...
hi!,
I am configuring connection interval time is 7.5ms ,
and slave latency is zero.and every connection interval event I am sending 1 packets (and my data lenth is only...
