I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
hi Engineers!
I am trying to use int. pullup of 160k but no effect. the voltage remains zero on pin.
config.resistor_p = NRF_SAADC_RESISTOR_PULLUP;
what problem?
...
Hi All,
sometimes i have a problems with bonding: the Nordic APP said "Couldn't pair with xxxxxx because of an incorrect PIN or passkey".
Why i have this errors? What...
Hi guys,
i'm trying experimental_ble_app_queued_writes out. I have some strange behavior.
The qwr service is
6e400001-b5a3-f393-e0a9-e50e24dcca9e but the characteristic...
I am developping NUS server(Peripheral) on Android. Central is ble_app_uart_c on nRF52832.
In this case, service discovery cannot be completed.
According to the console...
Hi. I am new with KEIL MDK and Nordic and ARM .....
I will create an MIDI BLE, but maybe anybody has an working Example for this?
Or what for an Example i can modify?
...
Hello, when I try to compile old working projects in SDK 11.0 with both Device Family Pack 8.5.0 and 8.11.1 (which I am using for SDK 13), I am running into the following...
Hello,
some time ago I was struggling with interfacing an I2S microphone with the nRF52832. That remained unsuccessful. My conclusion back then was that the selected I2S...
Hello, i use ibeacon example, this is the reader advertising packet, he has 31 byte long:
0201041AFF590002150112233445566778899AABBCCDDEEFAB010200FFC300
in this packet...
(/attachment/fad3a1e781331c528a9db48ec177b9b7)Hi there! i need help. I am using NRF52Dk with Bluetooth developmebt studio.
I set up my custom service in BDS an then imported...
Hello, i have a NRF51822 beacon and a reader, i read a advertising data:
0201041AFF590002150112233445566778899AABBCCDDEEFAB010200FFC300
i know that the uuid is:
0112233445566778899AABBCCDDEEFAB...
Hello!
We are doing transfer from an Android app to a device using nRF52. We don't get the transfer speed I have seen other achieve. I get between 8.5-10 kbps. As a reference...
I added a few custom services the ble_app_hrs code. I tried to flash the code, it was successful, the device is advertising but not connecting in the nRF connect app. What...
hi,
i started a project based on the ble_app_uart_c example and i have a working connection with a central and a peripheral board. now i'd like to have two peripherals...
Hi fellows,
I'm trying to control accurate/deterministic timing of the first bit from MOSI PIN of SPIM, employing EasyDMA.
According to Figure 69 SPI master with EsayDMA...
