Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
I have NRF51822 Controller(custom board,S110) used to send some sensor data. i can able to receive data in android and ios. now i want to communicate to Laptop which has internal...
Hello Everyone,
I am new to nrf51822 (using S130). I made some custom service that accepts float numbers.
This might be noob question: I want to send float values from...
We are developing a custom ble service and profile however having printf makes our lives that much easier so we are trying to incorporate it purely for testing purposes. ...
Hello,
I'm trying to optimize my application :
I have a central (nRF52832 s132) which communicates for a short time to a peripheral (nRF51822 s130) and then disconnect...
Hi
I'm trying to register an fds_evt_handler() in SDK 14. I have several questions:
Should I be registering fds_evt_handler() with NRF_SDH_SOC_OBSERVER or NRF_SDH_BLE_OBSERVER...
Hi!
Is there any chance to get the Altium files for the nRF24L01 refmodule with PCB antenna? I found the files but for the SMA version and I'm trying figure out the same...
Hello,
This is Milav Soni from Teq Diligent,India.
I explore the nRF52 series Chip and nRF51 series chip.
I also explore some of your BLE video.
I have one question...
Hello,
I'm using SDK 13.0.0.1 to develop my project. For driver example, such as RTC, I can't see data log while I can see the data log for BLE example, such as ble_app_uart...
Hi @ all,
We discovered a bug in the Nordic TLS API, which only appears once a secure TCP connection that makes use of certificates is to be established.
The provided...
Hello All,
I'm developing a BLE sensor based on the nRF52832 which needs to do the following:
Use an (i)Beacon for the user to find the sensor with an App on a mobile...
nRF52832 has errata about gpiote as below.
3.29 [97] GPIOTE: High current consumption in System ON Idle mode
So I want to use PORT event for gpio interrupt, but PORT...
Hi all,
I programed hex file (blinky example) to nRF51DK via nRFgo Studio, and the board could work fine (keep blinky).
However, the nRF51DK will work FAIL (LEDs are not...
Hi,
I need to monitor voltage very frequently, have access to the latest value and also to have interrupt on low limit.
But I do not want to have interrupt on EVT_DONE,...
Does anybody knows exact number of the "4 SIG fixed group addresses"?
Is it 0x00? or other?
In the SIG document, there is below chapter.
Group Addresses
A Group...
