Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi
I'm setting up a firmware based on the DTM example to perform certification tests.
In the DTM example firmware I see that there is a VENDOR_SPECIFIC command option...
hi,
i tried nrf51822_beacon_app.hex( C:\Nordic Semiconductor\nRF51822 Beacon v1.1.1\Source Code\nrf51_beacon\ble_app_beacon\pca20006\s110\arm_build\ ).in that we changed...
This might not be the correct place/forum to ask this question.
Since a couple of days, I am not able to step or next with gdb .
I understand that gdb needs to know what...
Hi：
Now keil4 default is to use the 16_bit THUMB instruction set, if I want to set it to start the program using the 32_bit ARM instruction set, how should we do? thanks
Hi,
After reading some questions about these topics I became a little confused.
I want to count milliseconds, so should I use Systick_Handler or use Real Time Counter...
Edit 1
To narrow down I did this... Below is ble_dfu_init() from ble_dfu.c.
uint32_t ble_dfu_init(ble_dfu_t * p_dfu, const ble_dfu_init_t * p_dfu_init)
{
uint32_t...
I am running NUS and a custom service.
I have updated vs_uuid_count = 2 in softdevice_handler.c
Following other posts on the forum, I have stepped through the code using...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Hello everyone
I was not able to find any explicit statement regarding the use of the TWI_APP with easyDMA on the nRF52 series and SDK13.0.0.
I checked the examples...
Hello guys,
I am currently looking at the recommended schematic QFN48 with internal LDO setup and I have a few questions (sorry, if they are silly, I am a newbie).
...
Hi, I'm working on an extremely space-tight design and need some clarifications. It is an nRF52832 QFAA chip with a Johanson 2450AT18B100 chip antenna.
Up to this point...
Hi,
I would like to use higher dBi antenna instead of the DK pcb antenna. Can I say the pi-network before J1 (measurement point) probe is 50ohm? Hence I can just remove...
I am trying to control another BLE device with nRF52xx. For controlling the device I need a terminal for connecting, disconnecting and switching on & off a sensor. I have...
I am using NRF52DK and trying to debug an SPI transfer, using SEGGER_RTT.h to print. However, printing of the logs are not consistent. Some debug lines do no appear in the...
