I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I want to design a BLE enabled display panel, which is a general purpose panel leverage all kinds of resources from mobile phone, including sensors, interaction, network,...
Since Nordic offers BLE sniffer tools including its hex code, I would like to flash it to my own USB dongle as a test. I insepected the hex code, and found its address starts...
Hi All,
I am new to the nRF processors (but not new to embedded progarming). Trying to use the evaluation board with the examples on the SDK. After realizing the freeware...
Q0. What IRQ Priority does BLE Has? and also what IRQ Priority does UART can have?
I'm guessing that from s130's document P65, Exception Model, It says,
Softdevice Timing...
Hello,
I could not set breakpoint in Eclipse. I set CFLAGS to -O0 and -g3 in Makefile
I am using GNU Tools ARM Embedded 6 2017-q1-update and Eclipse Neon3
Below are...
Hi,
is at the moment possible with S110 (nRF51 SDK) to whitelist only SOME of bonded peers? I need to allow connection from one selected central. Selection is made by user...
As a follow up from devzone.nordicsemi.com/.../ , I am now trying to find out if I am getting all of the memory settings put together correctly. When I have them at higher...
I am using nrf51822, 16K RAM, 256K Flash.
From the movie , there is no way to secure my firmware for DFU. Is there any other way to secure my firmware?
Thank you
I know the many differences coming in bt5. Will the programming concepts be the same in the upcoming 5 version? IF my code is working with ble4.1 will it automatically work...
After a bunch of headache I was able to successfully program with the nRF51822 Development Kit without the nRFgo Starter Kit motherboard, here is how I did it.
Hardware...
I'm working on a design that incorporates an nRF52832 along with some sensors and drivers.
Up to this I've been sacrificing power consumption in prototypes by using LDOs...
Hello,
Is it possible to change SPI baud rate whenever we want?
For example:
The initial SPI baud rate is set to 4M. We want to change the baud rate to "2M" to get...
Hi,
This may be stupid, but I can't declare classes in my .h file in keil. I have arduino library for my I2C device, but keil; does not recognize when I declare classes...
I've looked through and tried many examples on getting my SAADC to produce a temperature offset. About a month ago I had the SAADC working really well with a wheatstone bridge...
Hello,
What changes need to be made to the following tutorial to enable basic advertising with the Rigado BMD-300 on a custom board breakout board?
devzone.nordicsemi...
