I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello, I use BLE NUS since one year to service a device. I recently got to SDK13, using SD132.
When I use iOS9 everything is ok. But when I use iOS10, the tx characteristic...
Im on an nRF52832, using the BLE Mesh 0.9.1 alpha release
I've followed the DFU Quickstart guide, and have been able to DFU the app_green_s132.hex, which is the prebuilt...
hi,
i am using NRF52 custom board. i want to provide serial number to each board, which i want to read or write any time using my firmware. if i erase the bord it should...
Hi,
I have a BLE nano v1.5 from RedBear. I want to use s120 SoftDevice developed for the nRF51822 and for what i've read this is not available for programming with mbed...
Hello,
I have migrated from SoftDevice S130 2.0.1 to SoftDevice S132 3.0.0 and found one mismathing in ble_gap_evt_connected_t structure.
There is absent an own_addr...
Hi,
Is it possible to make pairing without the peer/device/bond manager? I am using SDK 12.3 on NRF51 and/or NRF52 and would like to get it to pair with a certain device...
Hi,
I'm using nRF52840 and S140 based on the ble_app_hrs_rscs_relay example. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu...
Within a buttonless DFU application should nrf_dfu_flash or fstorage be used to erase and write to flash?
SDK 13.0.0 - Soft device s132_nrf52_4.0.2_softdevice running on...
These messages below appeared when I built bootloader_dual_bank(sdk11) in the eclipse.
'Building target: bootloader_dual_bank_s130_sdk11.elf'
'Invoking: GNU ARM Cross...
I want to have blinky orange led,
0 mean on, 0x8000 is off, right? and why??
I have no idea what's 0x8000 mean!
so if I want have orange(full-R and half-G), how can...
I'm trying to debug my UWP Central app, which interacts with our device based on nRF52/s132. What I think I'm seeing with my packet sniffer (the nRF51 sniffer, incidentally...
I have set the
advdata.include_ble_device_address = true
in advertising_init function. However, the mac address data is not shown in mobile APP.
Is it due to the fact...
