Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
Hi,
I have a custom board where I have an nrf9161 main processor and an nrf54L05 processor connected with each other via I2C.
In this case, I'd like to manage the communication...
Hi
I've an application running on nRF Conenct SDK 3.0.2 on an nRF52840DK. Now I tried to enable update support over serial recovery of MCUBoot using the USB ACM.
First...
I have created the nRF Cloud Multiservice Sample application and would like to add WIFI support.
I am using nRF9151 with nRF7002 EK hardware and would like help in adding...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
Hi,
I am currently trying to integrate a digital microphone with the I2S peripheral of nRF5340 audio DK. I am accessing the P10 header of the nRF board for the particular...
Hi,
I need to enable an input interrupt on nRF52832 and I want to use a GPIOTE EVENTS_IN channel.
During boot configuration, I'm using nrfx_gpiote_in_init function with...
Hi, everyone. I would like to be notified about the brown-out on my device. I know about POF peripheral, but lowest possible threshold is NRF_POWER_THRESHOLD_V21 (which is...
First off, forgive me for being a newbie at ARM programming in general. In AVR this was straight forward.
I have a circuit connected like this to the ADC (P0.01 = AnalogInput2...
Hi,
I would like to transfer real time ecg data from a 3-channel adc (250 Hz per channel, 16 bits ) using nRF51822 to an android device. I would like to know if this is possible...
We are looking at using the Gazell protocol for a project. There isn't much information out there except for the "Gazell Link Layer User's Guide"
developer.nordicsemi.com...
Hi,
I've been working with a two LPC1768 boards with connections to Addicore nRF24L01+ boards.
I have not been able to successfully receive an ack on the PTX board although...
Hello
What is a typical current draw when using a PORT GPIOTE interrupt? I seem to be drawing approximately 200uA with a port event enabled. Is this normal?
I'm using...
Here: developer.nordicsemi.com/.../a00050.html
"The Bootloader/DFU with SoftDevice update example shows how a SoftDevice, bootloader, and pplication (sic) can be updated...
Hi,
I am trying to bring up custom board with 51822 CFAC-A0.
And I am continuously getting the following error as soon as the code does advertising_start().
I am using...
This comment for this line of code in twi_sw_master.c is misleading:
#define TWI_DELAY() nrf_delay_us(4) /*!< Time to wait when pin states are changed. For fast-mode the...
Hello all
I'm new to Nordic products and the Keil compiler and in order to fast-track my development I have two computers, home and work, running Keil MDK-ARM (lite) with...
As said on the topic "GAP Address types", the random static address can be changed when system boots up. I can't find any content about how to make it. Could anyone offer...
Hello,
I have a problem with getting i2c to work. What I did is enabled the 2-wire block, and tried to send various data as a master(by setting the registers), but I cant...
Hi Nordics.
I want to change SDK version of my project from SDK 6 to SDK 8.1
(actually I am trying to restart my project with new SDK 8.1)
My project base on the ancs...
