Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
After the update from the SD4.0.2 to the SD6.1.1 (nrf52832), it is not anymore possible to pair with the OnePlus5 (Android 9.0) With the Galaxy Note8 (Android 9.0) it works...
Hello,
So I assume VDD is from USB or the battery depending on whether USB is there or not. So, when the SAADC outputs ~3.258 V (in low power mode) that's fairly correct...
I need to measure with SAADC two channels in the same time (NRF_SAADC_INPUT_AIN6 and NRF_SAADC_INPUT_AIN4).
Is possible ?
Have you an code example?
Thanks
Marco
Hi,
I used a nRF51 dongle (PCA10031) wit the nRF Connect (v3.3.0) Bluetooth Low Energy application to communicate with a MBN52832 development kit. This works great until...
Hello:
I am looking for the best way to capture the SD and application error/fault(s) so that when the device is restarted, the data can be transmitted to the central...
Hi
I have installed the toolchain according to the getting started assistant, nRF Connect SDK v1.1.0
I try to load the asset tracker application in Segger with CMake_lists...
want to add UART communication to nRF52832 with mesh enable.
I have added,
nrf_drv_uart.c
nrfc_prs.c
nrfc_uart.c
nrfc_uarte.c
files into nRF_Drivers folder...
Hi,
Let's say I have a network with 5 NRF52833-DK and 1 smartphone with the NRFMesh App. How can I achieve to sniff all the ongoing packets in the mesh network on the smartphone...
Hi,
I have a customise board which has nrf52832 chip inside. I want to establish a secure connection between my 2 customised boards but I dont have any button or display...
Hi,
We are currently in development of a custom board with an nRF52840. I'd like to check my IO pin mapping using an IDE if possible, but I was unsure if Nordic or its partners...
Hello. I am using a Nordic Semiconductor Beacon (nRF 51822) and i am trying to connect it to my Raspberry Pi 4, but even though i installed Bluez, scanned using hcitool, i...
Hi,
I have nrf9160 DK. It is ok for ibasis SIM card. But if verizon SIM is used, there is no TCP/IP connection.
I tried to set APN by using:
AT+CGDCONT=1,"IP","vzwinternet...
Hi,
I'm trying to deploy the example program, cifar10, from CMSIS-NN library on NRF52. The issus is I compiled and downloaded it to the board successfully but when I try...