During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
After following the " Using a custom Secure Partition Manager with your application " Guide for the nRF5340-PDK, I experienced following error:
I tried to create a Non-Secure...
Hello every one.
I am new with Segger and nRF52.
I tried to create my own library for OB1203 sensor.
But i stack here when Segger view this error: Below is my screen...
As we are performing climate tests for custom PCB based on Nordic nrf52832 SOC, in low temperature i.e -20 Deg C the communication is not stable. After verifying the HFCLKSTAT...
Hi,
We thought to have a setup like this
1<-->2<-->3
1 is MESH ADV device with some mesh model
2 is MESH ADV + regular BLE stack support
3 is Gateway with...
I am trying to collect sensor data and store in flash using qspi interface. Unlike the peripheral example code, the qspi data handler function is not getting hit with ble...
Hello, I have another problem... i work on nrf9160 dk
I try to send http post when i pressed button 2 but this doesn't work.. Below you could see my code who block on printk...
I have been reviewing this merge: https://github.com/NordicPlayground/fw-nrfconnect-nrf/pull/1982 and it appears that there is capability in the fota example to enable https...
How to configure the start address and size of flash memory and nrf52832 in SES and how to calculate the size? How to calculate the start address and size of app and bootloader...
Hi,
Current Status:
I'm trying to run the fpu_fft example from the SDK 15.3.0 on my nRF52832 DevKit. When I clean and build the project in SES everything is fine and I...
Hi, I have a question about unknown flash data from MBR area which start from offset 0x0000035C, 20 bytes data show as below.
Data[20] : FF FF FF FF FF FF FF FF FF FF FF...
There doesn't seem to be any validation of the image when updating the bootloader by secure DFU. nrfutil has no switch to generate any crc or ecdsa_signature. The code uses...
Hi
I am making mesh network using Raspberry pi and NRF52 DK. I install bluez 5 and meshctl on raspberry pi. I successfully connected nrf52 dk using bluetooth. I attached...
I am doing this nRF52xx-to-Thingy-52 example: https://github.com/crfosse/Thingy-52-to-nRF52xx I am able to get the led part working fine, but when I finish the instructions...
I am trying to merge Softdevice, bootloader, bootloader setting and application. But unable to do in a single mergehex command. If i do merge seperately ((BL + SD + APP) with...
