Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi guys,
i tried to find information about the differences in chip revision
nRF51822-QFAA-R7, NRF51822-QFAA-T and nRF51822-QFAA-G0 but i can't find the R7 or T type anywhere...
1.
Are there any other resources than RTC/WDT requiring 32kHz LFCLK, not listed in Table 28 of nRF51422 PS (i.e. Radio)?
2.
ANT stack requires LFCLK +-50ppm, so +-25ppm...
Hello,
I'm getting an exception while starting MasterEmulator Sample Programs. All indicated Dlls were copied along with .exe, windows ver is 7. the same error happens...
Hello all,
I would like to send Acc and gyro data just like health temperature over nRF8001. Which Service can I use? How can I create one?
Thanks for help in advance...
I have BLE Shield V2.0 and i want to change the device name from the iPhone. We can use nRFGO Studio to change the name from GAP Settings but this is only one time change...
When using proprietary radio protocols only (Shockburst/Gazell) are there any difference between nRF514 and nRF518 chips? Do they behave totally equal so they can be used...
I need to send a data package when radio is ON every time
but I try to send data by "sd_ble_gatts_hvx()" I find it can not work,it seems that I can't call this API to send...
Hi
i'm new in dev zone and i have a question
now i work with nRF8001 and i want to design a pcb for it.
I want to reduce the BOM and for this i want to use only the internal...
Hi,
I am trying to use the DFU example provided in SDK 5.1.0. I have built the example using gcc 4.7.x, and i am also using softdevices 5.2.1. The DFU example has been...
Hi,
I've the need to write a characteristic value of 65 bytes, from my central device (iPhone/iPad) to a nRF51822 peripheral device, so I was looking at this document for...
Hi, sorry if this is a dumb question. I've just ordered some development kits and maybe that will answer the question, but i'm being a bit impatient!
I want to put an nrf51422...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi all,
In my project ,I use the SPI to communication between nRF51822 and STM32,but I don't know
how does the heart_rate data transmit to BLE stack.
I am confused...
We have a custom nrf15822-AA board flashed with the S110 (6.0.0) and our application. It has a 32khz crystal. It is connect to our (Mac) development systems with a SEGGER...
