I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hi!
I'm looking for a new Bluetooth module for a controller, and I run across the nRF51. I used to have a module that I controlled from the MCU, but this SoC looks like...
I am trying to use the NRF_LOG system with FreeRTOS. In the case of an ASSERT, I want to be able to:
1) log the location of the assertion
2) flush the logs over RTT
...
I’m using the library pc_ble_driver_py last release 0.14.1, and Nordic DevKit PCA10040. My goal is to set the central IRK value and generate a private resolvable address....
Hi, i am trying to build a ble beacon for personal asset tracking. The one that is like Tile or Trackr. What kind of chipset and program that i should use.
Hello
P airing: Just Works with Bonding: Passkey Entry, Peripheral Displays works for bonding.
I want to make LESC Pairing: Just Works with Bonding. Is it possible? According...
I got a vague "cmake did not complete" error from studio when the sdk was installed at a hgfs mounted disk. It worked ok when the sdl was installed at non-mounted directory...
the gy-80 module which has
1. HMC5883L
2. BMP-085
3. L3G4200D
4.ADXL345
i want to get the x, y, z axis of the sensor's position
which example i have to use and...
I am building a project with CMake, inside nRF SDK for Mesh 3.2.0, which uses the math library:
1. source file includes math.h
2. CMakeLists.txt adds m to target_link_libraries...
There are a lot of missing materials under the topic:
Software Development Kit > Previous versions of nRF5 SDK for Thread and Zigbee > nRF5 SDK for Thread and Zigbee v3...
I'm converting an already working LPN that went into SystemOFF with GPIO wakeup for lowest power consumption.
Now I want to use the RTC2 as a secondary wakeup.
I know...
I am currently developing on the nrf52840DK (Rev 1.1.1) using the mbed os.
To debug on the board using OpenOCD it is necessary to flash the JLink firmware for the board...
Dear Nordic community,
we as a company, have developed products with the nRF52832... currently, we're developing a product with the nRF52840 (because we needed USB).
My...
Hello
I would like to change the Tx_Power using softdevice.
The sd_ble_gap_tx_power_set command shows me the supported tx_power values as -40dBm, -20dBm, -16dBm, -12dBm...
I have make some custom board with the same layout as a BMD-300 evaluation board (pca10040) with the same MCU which is used on this evaluation board from RIGADO. This is BMD...
Hiya,
We're running a few experiments with a wireless-mesh protocol based on rapid flooding on a few nrf52833 dev kits.
We'd ideally like to use a channel contention mechanism...
