I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I'm new to nRF52 and the SDK, trying a few things to learn, so might be missing something obvious, but I've been looking at this apparent issue for a few days now. ...
I've based my application on ble_peripheral ble_app_blinky example.
So I used the following Code as model:
with:
for update and notification of a charachteristic...
Hi Devzone!
I'm using LM5(BG96) LTE modem to publish the mqtt message.
When I test it at PC terminal, It works very well. There is no problem.
However, when I send...
Hello,
I am currently working on a project which is a pcb design with NRF52810 . To set the gatt services I need to increas ram size by changing NRF_SDH_BLE_GATTS_ATTR_TAB_SIZE...
How can I modify the number of resends when Coap uses OT_COAP_TYPE_CONFIRMABLE, because I don't want to wait too long to get OT_ERROR_RESPONSE_TIMEOUT，
SDKs do have docs in markdown format. What is the recommended tool to be able to access all the features?
Tried MarkdownPad2, but it fails for example on @anchor tag.
...
Hello,
I have a problem statement in which I have to generate a file for data that is received from UART communication and want to send it to the mobile application whenever...
Hello guys,
For last couples of Days, we were trying to connect with IBasis NB-IOT Network with nRF9160 DK.
But not able to connect it .Please see below Snap Short for...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to send packet with different...
Hi,
In our project we are using the adc pin (p02) for batttery level measurement.
The analog dc signal from the battery is connected to p02 pin after the voltage is...
Hello,
Our peripheral device has no keyboard and no display.
Yet we would still like to have the most secured way of communication.
For our application, we don't like...
Apologies for the newbie question. Does this BLE Module need a separate antenna to be purchased? Or are you supposed to design your own with PCB traces? Some BLE modules have...
I want to avoid the soldering of the inside (Becoz of production isse) pins that's why I'm using all the outer pins of the ic. But the problem is RESET pin is inside so can...
Hello,
I am using UART_1 in my program to comminicate with other sensor. So the data is read from UART_1 and print to UART_0. Now I want to communicate with other sensor...
Hi, I am using BMD301 chip on my custom board which schematic i have shown below,I need to enable UART as well as nrf_log in my application. For this I am using SDK 15.3 PCA10040...
