Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Good morning; I am from Argentina, working in a Big Data Project using NoSQL and SQL tools. In fact, I deployed a architecture using Elasticsearch mixing ML, prediction, KPI...
Hello,
about two years ago we have made a Device basked on SDK 13 with S132 4.0.2 on it.
Now we had to build a newer version for our application and for this we have taken...
Hey.
I have a code for processor nrf51422 which compiles using a makefile. However, I decided to import it into a segger - with which I have no experience. For this I used...
Hi ,
I am just unable to find the FW ID for SD v7.0.1 anywhere.
I am using SDK 16.0.0 and SD 7.0.1 and would like to create a DFU package. Any of you know what is the...
Hi there,
I am trying to transmit data with high MTUs via pc-ble-driver-py. The data is sent from an nrf52840 with own firmware.
After the bug in nrfutil was fixed,...
Hi,
im trying to turn on LEDs on my custom nRF52 board. Im using LEDs on 13,14,15 pins. I config pins in pca10040.h to my LED pins, but they dont work. Also if i try to...
I am trying to set up multiple ble diagnostic type services for different sensor devices, from a single nrf52840. The services share a common base id and some have the same...
hi! I'm trying to use the following to configure the GPIOs in nRF52DK for the LED blinky.
nrf_gpio_cfg_output(pin_number)
But I'm not sure what number should I use for...
Hi Nordics,
all the examples provided for searching for advertising peripherals use some sort of filter ( NAME, MAC, UUID, WHITELIST etc) . My questions is: Is it possible...
Hello Nordic Team
I m working in BLE project .
1)I want to get list of scanned devices .
2) I want to store the scanned devices in array .
3) I want to connect with...
Hi everybody
I use the nrf52 SDK (nrf5_SDK_15.2.0) to develop the IoT application of BLE. The IoT device acts as the TCP server and the BLE gateway acts as the TCP client...
Hello,
What is the least version should I buy to for nRF52732 software development.
Keil offers Essential and Professional versions, but the price doubles for Pro.
Our...
Currently I am developing application which run on nRF52832. In this application I have to decode and encode messages using RSA 2048-bit keys pair. Currently I am using ARM...
Hi,
I just want to know if this is an expected behaviour of the Softdevice. I have a central that scans every 2 seconds for 1.7 seconds (leaving 300ms for connections...
