Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I am trying to build one of the Thread examples.
nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b\examples\thread\simple_coap_client\pca10056
Keil uVusion V5.15
When...
Hi everyone,
my problem is pretty simple: we developed a custom board for the NRF52840 to work using a custom protocol or BLE. A few sensors are connected to the NRF using...
Hi,
I am using NCS v1.1.0 and modem fw 1.1.0.
We had prepared our application in NCS v1.0.0 and now i have moved it to v1.1.0.
In new sdk v1.1.0 ,When i try to get Address...
Hello , I am advertising from a nrf device with advertising interval of 40ms. and I want to measure this interval at scanning side.
How I can measure using timer , timer...
I am using nRF52 DK to evaluate the TX power settings using sd_ble_gap_tx_power_set command:
sd_ble_gap_tx_power_set ( BLE_GAP_TX_POWER_ROLE_CONN , m_conn_handle, tx_power...
I have a project that needs to scan and filter the advertising name, uuid and mac address from the device. I will set them one by one and enable them one by one. I set them...
My problem seems to be a lot like case numbers 217967 and 243215.
I do not have an oscilloscope or logic analyzer.
I am using a nRF52840 DK (PCA10056 1.0.0 2018-17) and...
I've just received my nRF9160 development kit this morning and after trying to setup the development environment for a few hours I've come to a halt.
I got it working...
I am looking to use libuarte in our project. We are creating a battery powered device and so need to be low powered. EasyDMA draws about 1mA when running which is far too...
Hello,
We are developing an application that is trying to receive a steady stream of bytes from a serial port. But we constantly get a fatal error when we call app_uart_get...
I'm running 6 X Thingy:91s in pre-production for use as a GPS tracking/iOT solution. Currently I'm located in Austin, TX. If I do not request GPS, I receive regular data from...
Hi all, I'm working with NRF52DK using Segger Embedded Studio with NRF SDK 15.0 trying to communicate to a UART sensor using the serial port abstraction layer API. Following...
Hi all, I'm facing an issue communicating with a UART-based sensor on the NRF52DK (52832). I've followed the serial_port example and using various forum topics I've got to...
