Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send data from sensor over bluetooth...
When i used Port 0 assigned on Uarte rx tx pin , everything was ok.
But when i changed the rx tx pin to port 1 , for example p1.00,p1.08.p1.09, it doznt work...
i am sure...
I use nrf5_SDK_for_Mesh_v3.2.0_src , nRF5_SDK_15.3.0_59ac345 and board pca10040.
Copy the ble_app_uart_coexist folder into the examples/ble_peripheral folder at your nRF5...
Hello.
I'm doing a DFU customization now.
However, because of the problem of data transmission of the last packet of the first page when advertising,
connection and...
I am setting up a relatively complex project that runs on top of FreeRTOS and it is based on the HRS freertos sample app from SDK 16.0.0. The device will need to run in several...
Hello,
I am trying to setup a PAN coordinator by following these steps:
1. mlme_reset_req() -> successfully responds with a mlme_reset_conf_t by calling the callback...
Hi,
I am using 52840 (WLCSP package) in a design. I am a hardware guy and no SW guy has been assigned to this yet. Can you please check my SPI pin assignment below and let...
Hi, I want to know if it is possible to use IOT sim card in India. Is there in any network provide such sim-card? Other than that, which example in SDK I should refer for...
Central info SDK: 15.3 nRF52840
Peripheral info SDK: 13.1 nRF52832
Number of connected devices Central 1: Peripheral 15
Connect these devices and leave them alone. If...
I collecting Heart Rate data using nRF52 and Max30102
I saw data in hyperterminal, it is normal and not show duplicated data,
but, I connected with my phone and nrf52...
Dear Nordic Developer Zone,
I have incorporated LESC in the following development environment. 【Development environment】 ・nRF51822 ・SDK12.3
The following function is executed...
Hi, all
I'd like to get the whole thread network topology (like nRF_TTM does) on raspberrypi, can this function be realized with wpantund or wpanctl?
Is "wpanctl mfg....
