here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi am using NRF52 board ...and am trying to send data(which is not a string) using ble_bus_string_send . I send data only once from a one second timer but the other side is...
Hi all!
I'm working on an nrf51822 (technically right now I'm using the PTR5518 as I'm still prototpying), and trying to set up a voltage divider on my pcb in order to...
Hi,I am debuging my programm base on SD-110-V6.0.0 ,sdk-V5.2.0. When I use the
static void characteristic_disc_req_send(const ble_ans_c_t * p_ans, const ble_gattc_handle_range_t...
Hi everyone,
I have a nrf51-dk. I am running Master Control Panel app on my win7 computer. However, I cannot see my nrf51-dk in discovered devices section. Log says, Loading...
I am working on an application for the nRF52 Preview board, using SDK 0.9.2. I need to acquire about five analog samples from a single channel at roughly 100 Hz, then wait...
I use SDK9.0,SD8.0,the device is 51822AC,the device can enter to Bootloader mode.
As it shows below.
Then I selected the .zip file to start DFU
But when it reached...
I'm trying to do all my development on linux, mostly so that I can use a continuous integration environment. I'm setting up a server to compile my firmware app on every pull...
Hello I am currently using the NRF52 DK2 PCA10040 with S132 soft device (nRF52 SDK v0.9.2) . I have setup my code to sample 4 analog pins periodically. I configured double...
Hi everyone,
Well, our device is based on NRF 51822 CFAC MCU. It’s an ibeacon based device which advertises and receives data frequently, and writes data into flash memory...
Hi,
I have a project that uses PStorage and the Nordic UART Service. PStorage is used to store a variable that is updated by the device, irrespective of the Bluetooth,...
Question:
From ble device I have to send some data or character to mobile in connected mode. After sending that data the device is not going to sleep mode while connected...
I'm trying to modify the beacon properties of the nrf Beacon in the nRF Beacon APP but it doesn't allow me to change those properties.
If I use the Beacon scanner the device...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi, I tried it from my Nexus 5, using the Android version of MCP. I can connect/unconnect, detect link loss, and (apparently) everything else, but only LED 1 seems to behave...
I want to connect one peripheral to a few central devices (lets say 3) but the central devices don't need to be connected to the peripheral at the same time. Should the PERIPHERAL_LINK_COUNT...
