I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
I'm trying to buy more data for my iBasis SIM cards that are provided with the nRF9160. I have 4 registered SIM cards and it was easy to buy more data through iBasis in the...
Hi,
I want BLE and ZIGBEE to be able to switch dynamically during running.Only one mode(BLE or ZIGBEE) is running at a time.If switching from zigbee to BLE, how do I turn...
I have implemented DFU functionality in my Bluetooth mesh project and used device A as the distributor and device B as the node to be updated. I have already configured both...
We have our firmware developed with ncs2.7.0 and everything works as expected. However, with a recent effort of moving to ncs2.9.1, the same project can be built but during...
When calling the bt_conn_le_create_synced function to create a connection to a peripheral, which is synced to the PAwR train, I get a CONNECTION FAILED TO BE ESTABLISHED ...
I have a BMD 350 nrf52832 module connected to nrf52DK board via P20 header. I am using nrf52DK to flash the firmware onto BMD350. my code works with nrf52DK and it logs onto...
We are trying to increase the TX output power on the nRF5340 when using Enhanced ShockBurst (ESB) . According to the product specification, the nRF5340 supports +3 dBm TX...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
Hello
I'm currently working on writing some specifications for a future product. In this product, I want to use the advertising mechanism to send specific data from one...
Hello,
I recently acquired a Thingy91 board in order to make a hardware prototype. I already have experience developing with the nRF52840 so I took inspiration from my working...
we don't seem to have power numbers for the 54L, but in the 5340 datasheet it shows the LFXO (0.16uA) used less power then the LFRC (1 uA).
Is that true with the NRF54L...
Hello, I am working on a project using a custom hardware configuration based on nRF5340 and nRF7002 similar in configuration to the nRF7002-DK, except without the on-board...
Hi!
We're building a project for the nRF54 where we want to run an external library on the FLPR core.
Right now we have a prototype PCB with a module from Fanstel on it...
